Product Search
Search results for 'C150'
Showing 181 - 200 of 1124 Total Results
CA-0212
Location: Cylinder Transport
Sample cart is painted steel with two shelves. Overall dimensions 34" x 17" x 31 ½" (864 x 432 x 800 mm). Load capacity is 400 lbs. (181 kg). Ships unassembled.
(3) options
Location: Aggregate Washers
Aggregate samples are automatically washed with Test Mark's aggregate washers to remove clay and other fines passing a No. 200 sieve.
CA-2700
Location: Specific Gravity Flasks
The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.
Muffle Furnace 4 1/4" x 5" x 6"
CA-1480
Location: Muffle Furnace
Test Mark's small bench-top muffle furnace features heating elements on top and side to provide uniform temperature.
CA-1485
Location: Muffle Furnace
Test Mark's small bench-top muffle furnace features heating elements on top and side provide uniform temperature.
Marshall Compaction Stationary Mold, 4"
AA-0045
Location: Marshall 4" Compaction Molds
Marshall Compaction Stationary Mold is for hand and non-rotating base compactors and is machined from seamless tubing and plated - from Test Mark Industries.
Cylinder Platen, 6 ½” Diameter
(3) options
Location: Test Platens
Free floating bearing platen seats under test pressure.. Used when testing 6” (152 mm) or 4” (101 mm) diameter concrete cylinders in compression. Platen is manufactured from steel with all components plated for corrosion resistance. Upper cylinder platen used when testing 6” (152 mm) or 4” (101 mm)...
CA-0793
Location: Min/Max Thermometers
Eliminates all of the problems associated with mercury separation and air bubbles trapped in traditional thermometers. Weather resistant rugged plastic case for outdoor use. Displays three independent temperature readings of current, maximum and minimum since last reset.
(4) options
Location: Retainers & Pads
Test Mark supplies grout sample unbonded capping system for compression testing of grout specimens in concrete testing environments.
CA-0217
Location: Cylinder Transport
The steel concrete cylinder carrier from Test Mark is used for carrying 6-inch dia. cylinders in the field or lab.
Density Drive Sampler, 3" ( 76.2 mm)
SA-1355
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 3" model.
Density Drive Sampler, 4" (101.6 mm)
SA-1360
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 4" model.
CA-2590
Location: Moisture Encounter
The concrete moisture encounter from Test Mark provides an instantaneous, nondestructive moisture measurement on concrete floors.
CA-0970
Location: Test Hammer (Rebound)
The calibration test anvil from Test Mark Industries is used to check the calibration accuracy of a test hammer.
(2) options
Location: Canvas Wraps
Neoprene pad inserts from Test Mark are made from a tough elastomeric material that evens out and fills irregularities in the ends of concrete cylinders to assure even distribution of test loads for consistent results.
Stainless Steel Clamp Assembly
CA-0600-07P
Location: Parts & Accessories
Stainless steel clamp assembly. Plastic Roll-A-Meter Kit replacement parts.
AA-0095
Location: Vacuum Pump
Direct-drive, two-stage, rotary-sliding, vane-high vacuum pump features a gas ballast and trap to reduce risk of oil being sucked into the system.
SA-0113
Location: Sample Ejector
The Soil Sample Ejector from Test Mark is used for removing soil samples from molds up to 7 in. long and 2, 3 and 4 in. dia. Shelby Tubes.
Marshall Automatic Triple Compactor, 4" Rotating Mold
AA-0024
Location: Marshall Automatic Compactor
Automatically compacts three samples at a preset number of hammer blows and shuts off automatically on completion. Unit includes compactor, automatic counter, oak pedestal and 4" mold.
