Product Search
Search results for 'D5581'
Showing 461 - 480 of 1124 Total Results
Test Mark Industries supplies manuals and literature for its construction materials testing equipment products.
(4) options
Location: Volumetric Flask
Test Mark Industries supplies volumetric flasks as part of a complete line of materials testing equipment.
CA-2980-01
Location: Aggregate
8 oz. test bottles are graduated in oz. and ml and have watertight screw-on caps.
Rhoma-Sol™ Specialty Emulsifier
AA-3128
Location: Emulsifier
Spray-on solution used to remove bituminous deposits and stains from test equipment, contains no hazardous petroleum solvents and is 100% biodegradable.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
CA-1515-S
Location: Sifter, Laboratory
Designed to accept up to 10 - 8" dia. full height sieves or 6 12" dia. intermediate height sieves plus pan and cover. Sifter quietly rotates and taps sieve frame from below with plastic composite tamper.
(4) options
Location: Tamping Rods for Concrete
Tamping rods from Test Mark eliminate air voids in concrete when making slump tests, concrete cylinders or conducting concrete air entrainment test.
CA-2670
Location: Specific Gravity Flasks
The le chatelier flask from Test Mark is used to determine the relative density of cement or sand and other fine materials.
Cube Molding Retainers and Pads
(3) options
Location: Cube Retainers and Pads
Cube retainers and pads are used with retainer caps in the cube molding system; pads are molded for consistent shape and thickness - from Test Mark.
(6) options
Location: Concrete Sensors
Durable, waterproof concrete sensors that monitor the environmental conditions within the concrete as it hardens. Models are available for both temperature and relative humidity monitoring.
SA-1000
Location: Preparation Tools
The preparation knife from Test Mark Industries is used for sample preparation and general lab work.
(3) options
Location: Wash Bottles
Test Mark Industries supplies wash bottles as part of a complete line of soil testing equipment and supplies.
Copper Condenser w/inlet, outlet tubes
AA-1004
Location: Asphalt
Copper condenser with inlet and outlet tubes. Product AA-1004; Test Mark Industries.
Copper Condenser w/inlet, outlet tubes
AA-2004
Location: Asphalt
Copper condenser with inlet and outlet tubes. Product AA-2004; Test Mark Industries.
(3) options
Location: Vertical Cappers
Test Mark's heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder.
CA-0810
Location: Planeness/Thickness Gauges
Test Mark's magnifying crack comparator simply monitors cracks in concrete and masonry structures.
(7) options
Location: Graduated Cylinders
Polypropylene graduated cylinders from Test Mark have a single scale with raised numerals for easy reading.
(4) options
Location: Retainers & Pads
Test Mark supplies grout sample unbonded capping system for compression testing of grout specimens in concrete testing environments.
CA-3032
Location: Flow Tables
Measure is calibrated to 400 ml and is used to determine air content of hydraulic cement mortar. Cylindrical measure is 3" (76 mm) ID and approximately 3 15/32" (88 mm) deep.
Liquid Limit (manual) Test Set
SA-0352-S
Location: Liquid Limit Test Sets
Manual liquid limit test sets are part of Test Mark's complete line of soil testing equipment. Easy, secure online ordering.
