Product Search
Search results for 'C1170'
Showing 501 - 520 of 1648 Total Results
3" x 6" & 2" x 4" Vertical Capper
CA-0130
Location: Parts & Accessories
These heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder. Place cylinders against adjustable guides on vertical arms for precise...
CA-0191-60
Location: Parts & Accessories
These neoprene pad inserts are made from a tough Elastomeric material that evens out and fills irregularities in the ends of concrete cylinders to assure even distribution of test loads for consistent results.
CA-0191-70
Location: Parts & Accessories
These neoprene pad inserts are made from a tough Elastomeric material that evens out and fills irregularities in the ends of concrete cylinders to assure even distribution of test loads for consistent results.
CA-0200
Location: Parts & Accessories
These pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set.
CA-0203
Location: Parts & Accessories
These pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set.
CA-0202
Location: Parts & Accessories
These pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set.
CA-0380
Location: Parts & Accessories
The Material Pan is used for performing concrete and aggregate test preparation. Made from sturdy 16-gauge steel that is plated for corrosion resistance. Comes with two heavy-duty carrying handles for easy transport.
CA-0382
Location: Parts & Accessories
The Material Pan is used for performing concrete and aggregate test preparation. Made from sturdy 16-gauge steel that is plated for corrosion resistance. Comes with two heavy-duty carrying handles for easy transport.
CA-4060
Location: Sand Equivalent
Test Mark carries sand equivalent test sets as part of a complete line of aggregate testing products.
CA-0242
Location: Parts & Accessories
This caliper accurately measures the ends of concrete cylinders. Range is 6" x 0.0005". Zero calibration, on/off switch and protective carrying case. Jaw depth is 1.5".
CA-2570
Location: LA Abrasion
The LA Abrasion Machine from Test Mark tests crushed rocks, slag and gravel for resistance to abrasion.
Air Bleeder Valve Cap and Gasket
CA-0500-5G
Location: Parts & Accessories
Air Bleeder Valve Cap and Gasket. Pressure meter replacement parts; Test Mark Industries. Needs CA-0500-07 Air Bleeder Valve Gasket...
Test Mark Industries supplies manuals and literature for its construction materials testing equipment products.
CA-2980-01
Location: Aggregate
8 oz. test bottles are graduated in oz. and ml and have watertight screw-on caps.
Rhoma-Sol™ Specialty Emulsifier
AA-3128
Location: Emulsifier
Spray-on solution used to remove bituminous deposits and stains from test equipment, contains no hazardous petroleum solvents and is 100% biodegradable.
Test Mark Industries supplies calibration and service locations for its construction testing equipment.
CA-0793
Location: Min/Max Thermometers
Eliminates all of the problems associated with mercury separation and air bubbles trapped in traditional thermometers. Weather resistant rugged plastic case for outdoor use. Displays three independent temperature readings of current, maximum and minimum since last reset.
CA-1515-S
Location: Sifter, Laboratory
Designed to accept up to 10 - 8" dia. full height sieves or 6 12" dia. intermediate height sieves plus pan and cover. Sifter quietly rotates and taps sieve frame from below with plastic composite tamper.
AA-0150
Location: Parts & Accessories
Excel Clean HD from Test Mark is approved by many state DOTs for centrifugal and vacuum asphalt extraction tests.
Cube Molding Retainers and Pads
(3) options
Location: Cube Retainers and Pads
Cube retainers and pads are used with retainer caps in the cube molding system; pads are molded for consistent shape and thickness - from Test Mark.
