Product Search
Search results for 'C780'
Showing 1 - 21 of 563 Total Results
Modified Vicat for Masonry Mortars
CA-3120
Location: Vicat Apparatus
The Modified Vicat Apparatus determines the consistency and consistency retention of mortar used with brick and block applications.
CA-0851
Location: Cement
Penetrometer Foot is a stainless steel disk, 2.70" (68.58 mm) dia. for use with masonry mortars to determine board life and initial consistency.
CA-3032
Location: Flow Tables
Measure is calibrated to 400 ml and is used to determine air content of hydraulic cement mortar. Cylindrical measure is 3" (76 mm) ID and approximately 3 15/32" (88 mm) deep.
Modified Vicat for Consistency and Set Time
CA-3115
Location: Vicat Apparatus
The Modified Vicat Apparatus from Test Mark Industries tests hydraulic cement mortars.
CA-3110
Location: Vicat Apparatus
Modified Vicat Apparatus from Test Mark is used for false set determination of Portland cement mortar.
Masonry Series Testing Machines
(8) options
Location: Manual Compression Testing Machines
Test blocks, masonry prisms, pavers and retaining wall units., Testing range from 1% to full machine capacity, with an accuracy of ±.5% of indicated load., Optional accessories for testing a full range of concrete and cement products. . Request a Quote Masonry series machines are available in two...
CA-3100
Location: Vicat Apparatus
The Vicat Consistency Apparatus is part of a complete line of cement testing equipment from Test Mark Industries.
CA-3150
Location: Gillmore Apparatus
The Gillmore Apparatus is used to determine initial and final set times of Portland cement, masonry cement, hydraulic hydrated lime and certain mortars.
Blaine Air Permeability Apparatus
CA-2970
Location: Blaine Air Permeability
The Blaine Air Permeability Apparatus from Test Mark determines the fineness of Portland cement on terms of specific surface expressed as total surface area in square centimeters per gram of cement.
CA-0850
Location: Pocket Penetrometer
The Concrete Pocket Penetrometer from Test Mark is lightweight for field and lab evaluation of the initial set of concrete mortar based on ASTM C-403.
Mortar Penetration Resistance Apparatus
CA-2830
Location: Mortar Penetration Resistance
The mortar penetration resistance apparatus from Test Mark Industries determines the time of setting of concrete by penetration resistance.
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
CA-0610
Location: Air Entrainment/Roll-A-Meter
The lightweight aluminum Roll-A-Meter is used to determine the air content of concrete mixes, and is recommended for concrete containing lightweight aggregates, air-cooled slag or highly porous aggregates.
(5) options
Location: Manual Compression Testing Machines
Testing range of 300 to 30,000 lbs. (1.3 to 133.5 kN) with an accuracy of ±.5% of indicated load., Compact design requires minimal floor space. . Request a Quote The CM-30 was developed for testing concrete beams where accuracy and maintaining their required load pacing rate is an essential part of...
CA-3128
Location: Vicat Apparatus
The Brass Mold from Test Mark is used with the Modified Vicat Apparatus for Consistency and Set Time.
CA-4030
Location: Void Content
The void content apparatus from Test Mark is used to determine the non-compacted void content of a fine aggregate sample.
(8) options
Location: Manual Compression Testing Machines
Testing range of 2,500 to 250,000 lbs. (11 – 1,112 kN) with an accuracy of ±.5% of indicated load., Supplied with platen set for testing 6" x 12" (150 x 300 mm) cylinders using unbonded or sulfur capping method and steel safety guard doors., Continuous duty hydraulic pump runs quieter, cooler and...
(3) options
Location: Test Platens
Models available for testing 12” (305 mm) and 8” (203 mm) wide masonry units. . Both models feature large diameter spherical disk and seat assemblies, and platen bearing surface plane to .001” (.025 mm) in any 6” (152 mm) direction, through hardened to HRC 60 and plated for wear and corrosion...
SA-0200
Location: Sand Density
The Sand Cone Density Apparatus from Test Mark Industries determines the in-place density of soils.