Product Search
Search results for 'T283'
Showing 1 - 20 of 1647 Total Results
AA-0012
Location: Marshall Basic Compression Testing
Lottman breaking heads are used for testing tensile strength; 4" model.
AA-0013
Location: Marshall Basic Compression Testing
Lottman breaking heads are used for testing tensile strength; 6" model.
AA-0010
Location: Marshall Basic Compression Testing
The lower segment of Test Mark's Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
300K Compression Machine, iD Digital, 1/2 hp
CM-3000-iD
Location: Parts & Accessories
CM-3000 300,000 lbs./1334 kN Capacityü Accuracy and testing range of + .5% of indicated load from 1% to full machine capacity exceeds ASTM C-39 and E-4 specifications.ü Quiet running continuous duty hydraulic pumpsü Rigid load frames exceed ACI 363 frame elongation requirementsü Four digital...
CA-2910
Location: Cube Molds
Tensile sand from Test Mark Industries is specially graded natural silica sand to pass a No. 20 (850 um) sieve.
High Strength Capping Compound
CA-0100-HS
Location: Capping Compound
Test Mark's High Strength Capping Compound is easily melted, pours smoothly, has a high compressive strength, and gives consistent test results.
AA-0015
Location: Marshall Basic Compression Testing
The dial indicator consists of a maximum position brake assembly and guide sleeve. Accommodates 4" or 6" breaking heads. Graduations of 0.01" div., range 1.00"...
CA-0100
Location: Parts & Accessories
Test Mark's Ultra-Strength Capping Compound is used to cap the ends of concrete test cylinders so compression force will be evenly distributed to the cylinder during testing.
MA-1101
Location: Machine Accessory Lift
The machine accessory lift can raise 1,100 pounds easily with a detachable metal handle - changing out breaking heads or adding spacers is quick and easy.
Constant/Falling Head Permeameter Set
(5) options
Location: Permeameter Sets
Constant/Falling Head Permeameter Set for use with granular soils in determining the coefficient of permeability via the constant or falling-head method for laminar flow of water.
Constant Head Permeameter Cell
(5) options
Location: Permeameter Cell
The Constant Head Permeameter Cell from Test Mark is used to determine the coefficient of permeability by the constant head method for laminar flow of water through granular soils.
(5) options
Location: Manual Compression Testing Machines
Testing range of 300 to 30,000 lbs. (1.3 to 133.5 kN) with an accuracy of ±.5% of indicated load., Compact design requires minimal floor space.. Request a Quote The CM-30 was developed for testing concrete beams where accuracy and maintaining their required load pacing rate is an essential part of...
Masonry Series Testing Machines
(8) options
Location: Manual Compression Testing Machines
Test blocks, masonry prisms, pavers and retaining wall units., Testing range from 1% to full machine capacity, with an accuracy of ±.5% of indicated load., Optional accessories for testing a full range of concrete and cement products.. Request a Quote Masonry series machines are available in two...
Density Drive Sampler, 4" (101.6 mm)
SA-1360
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 4" model.
CA-0500-29
Location: Parts & Accessories
Pan head screws. Pressure meter replacement parts; Test Mark Industries.
High Capacity Series Compression Testing Machines
(3) options
Location: Manual Compression Testing Machines
Accuracy range of ±.5% of indicated load from 1% to machine capacity.. Request a Quote High capacity series machines feature rigid distortion-resistant load frames that are designed to meet the demands of testing high-performance concrete in a production testing program, where accurate and...
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders.. The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of test...
(8) options
Location: Manual Compression Testing Machines
Testing range of 2,500 to 250,000 lbs. (11 – 1,112 kN) with an accuracy of ±.5% of indicated load., Supplied with platen set for testing 6" x 12" (150 x 300 mm) cylinders using unbonded or sulfur capping method and steel safety guard doors., Continuous duty hydraulic pump runs quieter, cooler and...
Constant/Falling Head Permeameter Set, 2.5" (63.4 mm)
SA-2200
Location: Parts & Accessories
Constant/Falling Head Permeameter Set for use with granular soils in determining the coefficient of permeability via the constant or falling-head method for laminar flow of water. Funnel provides adjustable constant head reservoir. Top cap applies 5-10 lbs. of force against top stone or screen to...
