Product Search
Search results for 'D2171'
Showing 521 - 540 of 1648 Total Results
CA-0217
Location: Cylinder Transport
The steel concrete cylinder carrier from Test Mark is used for carrying 6-inch dia. cylinders in the field or lab.
CA-0280-P
Location: Cube Molds
The high-density polyethylene three-gang mold for 2-inch cubes strips and reassembles easily. Easy ordering online from Test Mark Industries.
CA-0300
Location: Parts & Accessories
Lightweight steel beam molds are used for molding third or center point test samples. Molds are hinge free to collapse into interchangeable parts for easy stripping, cleaning and quick reassembly with wing nuts.
CA-1515-S
Location: Sifter, Laboratory
Designed to accept up to 10 - 8" dia. full height sieves or 6 12" dia. intermediate height sieves plus pan and cover. Sifter quietly rotates and taps sieve frame from below with plastic composite tamper.
CA-3032
Location: Flow Tables
Measure is calibrated to 400 ml and is used to determine air content of hydraulic cement mortar. Cylindrical measure is 3" (76 mm) ID and approximately 3 15/32" (88 mm) deep.
Portable Precision Balance, 2200 g x 0.01 g
SC-0196
Location: Parts & Accessories
he Portable Precision Balance from Test Mark features selectable weighing units, percentage weighing and below balance weighing functions, stainless steel pan, adjustable feet, low battery indicator and auto-power shut off, manual internal calibration with built in mass, RS-232 and USB interface,...
SA-1300
Location: Probe Rod
The Steel Probe Rod from Test Mark is used for locating soft zones in and under compacted areas in sub-grades and footing excavations.
CA-0793
Location: Min/Max Thermometers
Eliminates all of the problems associated with mercury separation and air bubbles trapped in traditional thermometers. Weather resistant rugged plastic case for outdoor use. Displays three independent temperature readings of current, maximum and minimum since last reset.
CA-0500-43
Location: Air Meter Calibrators
Aluminum Air Meter Calibrator quickly checks the accuracy of any pressure-type concrete air meter with a .25 cu. ft. base - from Test Mark Industries.
Concrete Cylinder Length Measuring Device for 4 & 6''Dia-24''L
CA-0237
Location: Core Length
With the core length measuring device measurements can be taken at the center point of the sample's upper end as well as the 8 equidistant points along the circumference.
4" Lightweight Retainer Rings (2)
CA-0200-L
Location: Unbonded Capping (Retainers and Pad Caps)
Aluminum retainer rings are 35% lighter than steel caps to reduce fatigue. They are heat-treated and hard anodized for longer wear and durability and conform to ASTM C-1231 specifications.
Location: Soils
Test Mark's COE Manual Compaction Hammer features a recoil mechanism in the foot assembly to reduce impact fatigue.
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers.. The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel with...
MA-1101
Location: Machine Accessory Lift
The machine accessory lift can raise 1,100 pounds easily with a detachable metal handle - changing out breaking heads or adding spacers is quick and easy.
CA-0160
Location: Parts & Accessories
This melting pot rapidly and efficiently melts capping compound and performs other routine melting operations. 100°-320°F (37.8°-160°C) adjustable thermostat accurately regulates heat. 115 V, 60 Hz.
SA-2030
Location: CBR Accessories
Used in the application of surcharged loads on the soil's surface during soaking and penetration. Rust-resistant.
