Product Search
Search results for 'C-1252'
Showing 121 - 140 of 1123 Total Results
Sieve, 8" dia., #100 Mesh, Half Height, Brass Frame, Brass Mesh
CA-1850-08HB
Location: Parts & Accessories
Each test sieve is supplied with a Serial Number and a matching Certificate of Compliance. Overall height - Full 2 5/8", Half 1 5/8". Depth to cloth - Full 2", Half 1" FS - Full height, stainless steel mesh HS - Half height, stainless steel mesh FB - Full height, brass mesh HB - Half height, brass...
Sieve, 8" dia., #100 Mesh, Half Height, Brass Frame, Stainless Mesh
CA-1850-08HS
Location: Parts & Accessories
Each test sieve is supplied with a Serial Number and a matching Certificate of Compliance. Overall height - Full 2 5/8", Half 1 5/8". Depth to cloth - Full 2", Half 1" FS - Full height, stainless steel mesh HS - Half height, stainless steel mesh FB - Full height, brass mesh HB - Half height, brass...
(2) options
Location: Test Platens
One fixture tests both 4” and 6” beams. . Used to determine the modulus of rupture for both Center and Third Point beams with depths of either 4” or 6”. The upper heads load bearing blocks are easily changed for center or third point test configuration for either size beam. Bottom support blocks...
CA-0360
Location: Slump Testing
Slump cones from Test Mark Industries determine the slump of concrete in the laboratory or field. Easy and secure online ordering.
SA-1050
Location: Dispersion Mixer
Test Mark's soil mixer is for dispersing solid suspensions used in hydrometer method of testing sub-grade soils.
SA-1500
Location: Static Cone Penetrometer
Static Cone Penetrometers from Test Mark are used to evaluate the consistency of soils, their level of compaction and the bearing capacity of shallow foundations and pavement sub-grades.
SA-1000
Location: Preparation Tools
The preparation knife from Test Mark Industries is used for sample preparation and general lab work.
CA-4020
Location: Proportional Caliper
The proportional caliper from Test Mark is a timesaving device used for rapid determination of percentages of flat and elongated particles in coarse aggregate fractions of .375" or larger.
CA-2700
Location: Specific Gravity Flasks
The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.
Liquid Limit (w/counter) Test Set
SA-0310-S
Location: Liquid Limit Test Sets
Liquid limit test sets with counters are available as part of complete line of soil testing products from Test Mark Industries.
AA-0300
Location: Asphalt Mixer
Test Mark's asphalt/concrete mixer is ideal for sample or batch mixing in either laboratory or field. Easy and secure ordering online.
CA-0600-P
Location: Air Entrainment/Roll-A-Meter
The PVC and fiberglass reinforced Roll-A-Meter from Test Mark measures entrained air in any type of concrete, including lightweight mixes.
CA-0933
Location: Specimen Curing
The curing tank immersion heater from Test Mark has an adjustable thermostat and a 1,000 watt 15 amp incolloy shielded heating element that resists rust.
(5) options
Location: Yield Buckets
Steel yield buckets from Test Mark are used for determining the unit weight of aggregate for concrete.
Liquid Limit (manual) Test Set
SA-0352-S
Location: Liquid Limit Test Sets
Manual liquid limit test sets are part of Test Mark's complete line of soil testing equipment. Easy, secure online ordering.
Rhoma-Sol™ Specialty Emulsifier
AA-3128
Location: Emulsifier
Spray-on solution used to remove bituminous deposits and stains from test equipment, contains no hazardous petroleum solvents and is 100% biodegradable.
CA-2590
Location: Moisture Encounter
The concrete moisture encounter from Test Mark provides an instantaneous, nondestructive moisture measurement on concrete floors.
Feeler Gauge Stock, .001 - 12"L x 1/2"W with rounded ends
CA-0481
Location: Parts & Accessories
When used with the steel parallel bar, Test Mark's feeler gauge stock will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
