Product Search
Search results for 'T-205'
Showing 121 - 140 of 1124 Total Results
Density Drive Sampler, 4" (101.6 mm)
SA-1360
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 4" model.
Cover Plate for Bronze Cube Mold
CA-0280-C
Location: Cement
Bronze cover plate with filling holes used with bronze cube mold for capping compound compressive strength testing.
CA-0480
Location: Planeness/Thickness Gauges
Test Marks' steel parallel planeness gauge determines the planeness of testing machine platens, cylinder cappers and other testing accessories.
(6) options
Location: Scoops
Test Mark supplies a variety of round mouth and flat bottom scoops for use in the construction materials testing industry.
(4) options
Location: Manual Compression Testing Machines
Machine custom-configured to test cubes, Accuracy of ±.5% of indicated load from 1,000 – 100,000 lbs. (11 – 1,112 kN), Choice of 3 digital load-indicating systems, Quiet-running, continuous-duty hydraulic pump . Request a Quote The CM-0100 series is based on our CM-2500 machine, custom-configured...
CA-0360-S
Location: Slump Testing
Test Mark's portable slump test sets consist of a steel slump cone, tamping rod, and cast-aluminum test base with handle for easy transportation.
(2) options
Location: Surface Thermometer
Surface thermometers from Test Mark put the sensing element into direct contact with the surface to measure the temperature.
SA-2030
Location: CBR Accessories
Used in the application of surcharged loads on the soil's surface during soaking and penetration. Rust-resistant.
Sand Equivalent Shaker, Spring
CA-4055
Location: Sand Equivalent
The spring-type hand shaker from Test Mark Industries is more operator-dependent than the mechanical model.
(2) options
Location: 6" Cube Mold
This single cavity cube mold with base plate is used for compression testing of concrete cubes or mortar samples in the "Time of Initial" and "Final Setting" of concrete. Dimensions: 6" x 6" x 6" (152 x 152 x 152 mm).
SA-0245
Location: Shear Vane Tester
The pocket shear vane tester from Test Mark provides a quick and efficient method for determining shear strength values of cohesionless values of soils.
SA-1302
Location: Probe Rod
For protection against possible electrical shock when working around buried electrical lines. T-handle has high density nylon cover. Shaft is 1/2" dia. x 48" long, steel tip measures 5/8" x 3/4". NOTE : Because size and weight will vary with quantities ordered, we have reserved the freight charges...
SA-1500
Location: Static Cone Penetrometer
Static Cone Penetrometers from Test Mark are used to evaluate the consistency of soils, their level of compaction and the bearing capacity of shallow foundations and pavement sub-grades.
SA-0354-S
Location: Shrinkage Limit Set
The Shrinkage Limit Set from Test Mark is part of a complete line of soil testing equipment. Easy online ordering.
(5) options
Location: Yield Buckets
Steel yield buckets from Test Mark are used for determining the unit weight of aggregate for concrete.
4" x 8" Cylinder Lifting Handle
CA-0213
Location: Cylinder Transport
The concrete cylinder lifting handle from Test Mark can be used to remove cylinders from curing tanks safely. 4" by 8" model.
6" x 12" Cylinder Lifting Handle
CA-0216
Location: Cylinder Transport
The concrete cylinder lifting handle from Test Mark can be used to remove cylinders from curing tanks safely. 6" by 12" model.
SA-1300
Location: Probe Rod
The Steel Probe Rod from Test Mark is used for locating soft zones in and under compacted areas in sub-grades and footing excavations.
CA-0360
Location: Slump Testing
Slump cones from Test Mark Industries determine the slump of concrete in the laboratory or field. Easy and secure online ordering.
SA-4010
Location: Dynamic Cone Penetrometer
The Dual Mass DCP Standard Kit from Test Mark measures the shear strength of soil with a CBR between 0.5 - 100%.
