Product Search
Search results for 'D2171'
Showing 141 - 160 of 1648 Total Results
SA-0113
Location: Sample Ejector
The Soil Sample Ejector from Test Mark is used for removing soil samples from molds up to 7 in. long and 2, 3 and 4 in. dia. Shelby Tubes.
Excel Clean HD Biodegradable Extraction Solvents
(2) options
Location: Biodegradable Extraction Solvents
Excel Clean HD Biodegradable Extraction Solvent is approved by many state DOTs for centrifugal and vacuum asphalt extraction tests.
CA-0470
Location: Rubber Mallet
The rubber mallet from Test Mark is used to consolidate materials and release entrapped air in concrete molds, air meters, slump cones and unit weight buckets.
(5) options
Location: Unit Weight Buckets
Aluminum cylindrical unit weight measures from Test Mark have machined interior surfaces, carrying handles, true and even top and bottom surfaces, are water-tight and will retain form after repeated use.
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders.. The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of test...
CA-0360-S
Location: Slump Testing
Test Mark's portable slump test sets consist of a steel slump cone, tamping rod, and cast-aluminum test base with handle for easy transportation.
CA-0191
Location: Parts & Accessories
Our pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set. These neoprene pad inserts are made from a tough...
CA-0191-50
Location: Parts & Accessories
Our pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set. These neoprene pad inserts are made from a tough...
CA-2710
Location: Specific Gravity & Absorption Fine Aggregates
Test Mark's pycnometer is used to determine specific gravity of fine aggregates. Easy online ordering.
Aqua-Check Kit, 20 gram capacity
SA-0255
Location: Moisture Testing
The Aqua-Check from Test Mark is a portable system used for measuring the moisture content of a wide range of materials including sand, aggregates and soil.
High Strength Capping Compound
CA-0100-HS
Location: Capping Compound
Test Mark's High Strength Capping Compound is easily melted, pours smoothly, has a high compressive strength, and gives consistent test results.
(4) options
Location: Cylinder Molds - Steel
Test Mark Industries features steel concrete cylinder molds as part of a complete line of concrete testing equipment.
CA-2180
Location: Parts & Accessories
Aggregate samples are automatically washed to remove clay and other fines passing a No. 200 sieve. Inconsistencies and the high cost of manual methods are eliminated.
(3) options
Location: Aggregate Washers
Aggregate samples are automatically washed with Test Mark's aggregate washers to remove clay and other fines passing a No. 200 sieve.
CA-1450
Location: Gloves
Test Mark's heat resistant gloves are used for handling heated items when conducting laboratory work with ovens or hot plates.
SA-1050
Location: Dispersion Mixer
Test Mark's soil mixer is for dispersing solid suspensions used in hydrometer method of testing sub-grade soils.
Drive Tubes, 3" x 2.75" (76.2 x 69.9 mm), 10/pkg
SA-1371
Location: Density Drive Sampler
For use with Drive Sampler, 3" (76.2mm) x 2.75" (69.9mm) length, (3" x 0.01 ft3). Accessory to the density drive sampler.
