Product Search
Search results for 'T-135'
Showing 181 - 200 of 1123 Total Results
Exhaust Chamber for Bench Oven
CA-1425-04
Location: Ovens & Hot Plates
Exhaust chamber adapter is available for processing material where undesirable fumes are present. Encloses the oven exhaust and allows venting into a standard 3" (76 mm) stove pipe.
CA-0280
Location: Cube Molds
The 2-inch (51 mm) diagonal arrangement three-gang bronze cube mold from Test Mark makes three test cubes at a time.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
SA-1120
Location: Manometer Tubes
The economical, wall mount Manometer Tube from Test Mark is built for use with many permeameters.
AA-0005
Location: Marshall Basic Compression Testing
The Marshall compression machine from Test Mark features threaded rods and heavy duty steel crosshead, for nearly twice the rigidity of other load frames, for more reliable test results.
(4) options
Location: Cylinder Molds - Steel
Test Mark Industries features steel concrete cylinder molds as part of a complete line of concrete testing equipment.
Asphalt Dispenser, 4 Qt. (3.8 L)
AA-3000
Location: Asphalt Dispenser
Asphalt Dispenser features a round melting pot has stainless steel crucible & shell to facilitate easy clean up - from Test Mark Industries.
SA-1150
Location: Shelby Tube Permeameter
The Shelby Tube Permeameter from Test Mark allows you to perform permeability tests on undisturbed soil samples.
(3) options
Location: Round Pans/Mixing Bowl
Test Mark supplies round pans and mixing bowls for laboratory use in materials testing applications.
SA-1800
Location: Soil Grinder
Soil grinder prepares soil samples to designated particle size for accurate and repeatable test results. Unit grinds a one-pint sample in 15 seconds. Includes a No. 10 perforated stainless plate.
(4) options
Location: Beam Molds
Steel Concrete Beam Molds from Test Mark are used for molding third or center point test samples.
CA-0850
Location: Concrete Penetrometer
The Concrete Pocket Penetrometer from Test Mark is lightweight for field and lab evaluation of the initial set of concrete mortar based on ASTM C-403.
AA-0015
Location: Marshall Basic Compression Testing
The dial indicator consists of a maximum position brake assembly and guide sleeve. Accommodates 4" or 6" breaking heads. Graduations of 0.01" div., range 1.00"...
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
CA-2745
Location: Specific Gravity Bench
200 watt heater/circulator is attached to a stainless steel bracket that hangs on the water tank to maintain constant temperature.
Static Segregation Column Mold
CA-0359
Location: Self-Consolidating Concrete
The Static Segregation Column Mold is used to measure cohesiveness of SCC. Concrete is placed in the column and allowed to stand undisturbed. After 15 minutes, the top and bottom sections are evaluated for the amount of aggregate retained on a No. 4 (4.75 mm) sieve and segregation is calculated.
SA-2030
Location: CBR Accessories
Used in the application of surcharged loads on the soil's surface during soaking and penetration. Rust-resistant.
SA-2031
Location: CBR Accessories
Used in the application of surcharged loads on the soil's surface during soaking and penetration. Rust-resistant. Slotted.
