Product Search
Search results for 'E-1907'
Showing 221 - 240 of 1124 Total Results
(2) options
Location: Rebar Locator
Test Mark's Rebarscope™ locates reinforcement bars in concrete and determines their depth and size.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
CA-0700-02
Location: Concrete
Replacement cup and stopper for measuring concrete mortar in Chase air indicator testing.
CA-4060-07
Location: Aggregate
Wide mouth funnel suitable for directing the test specimen into the sand equivalent test cylinder.
Marshall Compaction Stationary Mold, 4"
AA-0045
Location: Marshall 4" Compaction Molds
Marshall Compaction Stationary Mold is for hand and non-rotating base compactors and is machined from seamless tubing and plated - from Test Mark Industries.
Feeler Gauge Set, .002 to .025
CA-0485
Location: Planeness/Thickness Gauges
When used with the steel parallel bar, Test Mark's feeler gauge will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
SA-1302
Location: Probe Rod
For protection against possible electrical shock when working around buried electrical lines. T-handle has high density nylon cover. Shaft is 1/2" dia. x 48" long, steel tip measures 5/8" x 3/4". NOTE: Because size and weight will vary with quantities ordered, we have reserved the freight charges...
Voluvessel, 1/20 cu ft capacity
SA-1400
Location: Voluvessel
The Voluvessel from Test Mark is a direct reading instrument that is easily used and requires no calibration. A liquid filled balloon measures hole volume after removal of soil sample.
Rhoma-Sol™ Specialty Emulsifier
AA-3128
Location: Emulsifier
Spray-on solution used to remove bituminous deposits and stains from test equipment, contains no hazardous petroleum solvents and is 100% biodegradable.
CA-2740
Location: Specific Gravity Bench
The Specific Gravity Bench from Test Mark weights suspended samples in water to determine specific gravity of aggregates and other materials.
(3) options
Location: Wash Bottles
Test Mark Industries supplies wash bottles as part of a complete line of soil testing equipment and supplies.
AA-0300
Location: Asphalt Mixer
Test Mark's asphalt/concrete mixer is ideal for sample or batch mixing in either laboratory or field. Easy and secure ordering online.
CA-4020
Location: Proportional Caliper
The proportional caliper from Test Mark is a timesaving device used for rapid determination of percentages of flat and elongated particles in coarse aggregate fractions of .375" or larger.
Copper Condenser w/inlet, outlet tubes
AA-1004
Location: Asphalt
Copper condenser with inlet and outlet tubes. Product AA-1004; Test Mark Industries.
Copper Condenser w/inlet, outlet tubes
AA-2004
Location: Asphalt
Copper condenser with inlet and outlet tubes. Product AA-2004; Test Mark Industries.
CA-0970
Location: Test Hammer (Rebound)
The calibration test anvil from Test Mark Industries is used to check the calibration accuracy of a test hammer.
Test Mark Industries list of authorized dealers and locations for its construction materials testing products.
Drive Tubes, 3" x 2.75" (76.2 x 69.9 mm), 10/pkg
SA-1371
Location: Density Drive Sampler
For use with Drive Sampler, 3" (76.2mm) x 2.75" (69.9mm) length, (3" x 0.01 ft3). Accessory to the density drive sampler.
Drive Tubes, 4" x 5.00" (101.6 x 127 mm), 10/pkg
SA-1372
Location: Density Drive Sampler
For use with Drive Sampler, 4" (101.6mm) x 5" (127mm) length, (4" x 0.033 ft3).
CA-0600-01P
Location: Parts & Accessories
Top expansion plug. Plastic Roll-A-Meter Kit replacement parts.
