WOC 2024

Product Search

Search results for 'C1176'

Showing 521 - 540 of 1658 Total Results

Digital Caliper, 6" (150 mm)

CA-0242

Location: Parts & Accessories

This caliper accurately measures the ends of concrete cylinders. Range is 6" x 0.0005". Zero calibration, on/off switch and protective carrying case. Jaw depth is 1.5".

Spacers for CM-0030 and CM-2500 series

(4) options

Location: Spacers

Spacers are used with test platens to adjust the vertical working clearance height inside a machines load frame, for testing samples of various types and sizes to prevent over-extension of the load frames piston. They are manufactured from steel and machined plane on both ends to maintain a...

Chapman Flask

CA-2700

Location: Specific Gravity Flasks

The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.

Wash Bottles

(3) options

Location: Wash Bottles

Test Mark Industries supplies wash bottles as part of a complete line of soil testing equipment and supplies.

Copper Condenser w/inlet, outlet tubes

Copper Condenser w/inlet, outlet tubes

AA-1004

Location: Asphalt

Copper condenser with inlet and outlet tubes. Product AA-1004; Test Mark Industries.

Copper Condenser w/inlet, outlet tubes

Copper Condenser w/inlet, outlet tubes

AA-2004

Location: Asphalt

Copper condenser with inlet and outlet tubes. Product AA-2004; Test Mark Industries.

CPW+ Series Digital Field Scales

(10) options

Location: Digital Field Scales

Digital field scales from Test Mark feature four selectable weighing units, 12-inch square stainless steel platform, remote indicator with large 1-inch LCD display, and water resistant keypad.

Soil Mixer & Cup

SA-1050

Location: Dispersion Mixer

Test Mark's soil mixer is for dispersing solid suspensions used in hydrometer method of testing sub-grade soils.

6" Test Cylinder Transport Rack

CA-0215

Location: Cylinder Transport

The test cylinder carrying case from Test Mark holds 8 - 6x12 test cyliners with anchoring holes which allow rack to be secured to truck bed.

Drierite Air Drying Unit

AA-0120

Location: Drierite

Easily installs in-line between vacuum pump and rice test equipment. Refillable unit measures 2 5/8" by 11 3/8" with hose barbs at both ends which will accept ΒΌ" to 3/8' flexible tubing. One of our Drierite products.

Sieve Storage Rack

CA-2080

Location: Sieve Storage Rack

This adjustable bench rack holds all diameters of sieves up to 12" (305mm) maximum. Stainless steel rack has non-skid rubber feet, and two permanent and two adjustable rubber-coated sieve support rods.

Test Cylinder

CA-4060-01

Location: Aggregate

Plastic measuring cylinders are 17 in. high, 1 1/4" inside diameter and are graduated from 0 - 15 in. by 0.1 in. graduations from bottom of cylinder.

Compaction Pedestal

AA-0032

Location: Asphalt

This pedestal stabilizes molds during compaction. 8 x 8 x 18" wooden post capped with a 12 x 12 x 1" steel plate. Mounts to a concrete slab with four angle brackets.

Speedy Moisture Reagent, 10 lb. can

Speedy Moisture Reagent, 10 lb. can

SA-0262

Location: Soils

Calcium Carbide Reagent is used with the Speedy Moisture Tester to create pressure proportional to moisture in test samples. Supplied in 10-lb. can.

8" Pressure Meter Lid Seal and Piston Seal for CM-4000 series Machines

8" Pressure Meter Lid Seal and Piston Seal for CM-4000 series Machines

CA-0500-23

Location: Parts & Accessories

Lid seal, 8 inch. Pressure meter replacement parts; Test Mark Industries.

Gasket Repair Kit - TMI

Gasket Repair Kit - TMI

CA-0500-39

Location: Parts & Accessories

Gasket repair kit. Pressure meter replacement parts; Test Mark Industries.

Replacement Latch & Pin for Gray Style Case

Replacement Latch & Pin for Gray Style Case

CA-0500-60L

Location: Parts & Accessories

Replacement latch and pin for carrying case. Pressure meter replacement parts; Test Mark Industries.

Triple Beam Balance

(3) options

Location: Beam Balance

Triple Beam Balance features magnetic damping, three graduated-tier beams, larger more stable base, factory installed security built into base and positive poise positioning, all standard.

Vacuum Extractor

AA-2055

Location: Vacuum Extractor

Vacuum Extractor from Test Mark is used for quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples.

Feeler Gauge Set, .002 to .025

CA-0485

Location: Planeness/Thickness Gauges

When used with the steel parallel bar, Test Mark's feeler gauge will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.