Product Search
Search results for 'C-535'
Showing 81 - 100 of 1648 Total Results
(3) options
Location: Test Platens
Used for testing 6” (152 mm) concrete cubes and cylinders in compression. The platens bearing block is 6.5” (152 mm) square, through hardened to HRC 55 or greater, plane to .0005” (.012 mm) in any 6” (152 mm) area, has concentric circles for easier centering of cylinders and is hard nickel plated...
CA-0245
Location: Vibrator
The lightweight electric concrete vibrator from Test Mark vibrates concrete test cylinders and molds in the laboratory or field.
Surface Thermometer, 0/250° F x 2° div.
CA-0800
Location: Parts & Accessories
This surface thermometer puts the sensing element into direct contact with the surface to measure the temperature. Dual magnet, 2" (51 mm) diameter dial.
(4) options
Location: Test Platens
Models available for testing up to 12” (305 mm) CMUs.. All models feature large diameter spherical disk and seat assemblies, and platen bearing surface plane to .001” (.025 mm) in any 6” (152 mm) direction, through hardened to HRC 60 and plated for wear and corrosion resistance. The bearing block...
AA-0095
Location: Vacuum Pump
Direct-drive, two-stage, rotary-sliding, vane-high vacuum pump features a gas ballast and trap to reduce risk of oil being sucked into the system.
(2) options
Location: Rebar Locator
Test Mark's Rebarscope™ locates reinforcement bars in concrete and determines their depth and size.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
6.5" dia. x 1" Thick Lower Platen
MA-0600
Location: Parts & Accessories
6.5" dia. x 1" Thick Platen.
CA-0355-SP
Location: Self-Consolidating Concrete
Test Mark's J-Ring Test Set is used to characterize the ability of self-consolidating concrete (SCC) to pass through reinforcing steel.
MA-1101
Location: Machine Accessory Lift
The machine accessory lift can raise 1,100 pounds easily with a detachable metal handle - changing out breaking heads or adding spacers is quick and easy.
High Strength Capping Compound
CA-0100-HS
Location: Capping Compound
Test Mark's High Strength Capping Compound is easily melted, pours smoothly, has a high compressive strength, and gives consistent test results.
Voluvessel, 1/20 cu ft capacity
SA-1400
Location: Voluvessel
The Voluvessel from Test Mark is a direct reading instrument that is easily used and requires no calibration. A liquid filled balloon measures hole volume after removal of soil sample.
(5) options
Location: Shelby Tubes
Shelby Tubes from Test mark feature a chamfered end that forms a cutting edge, and includes holes for securing tubes to a drive head.
SA-0354-S
Location: Shrinkage Limit Set
The Shrinkage Limit Set from Test Mark is part of a complete line of soil testing equipment. Easy online ordering.
Triple Beam Balance, 2610 g x 0.1 g
SC-0035
Location: Parts & Accessories
Test Mark's Triple Beam Balance features magnetic damping, three graduated-tier beams, 6-inch dia. stainless steel weighing pan, weight set, below balance weighing with unique removable tripod legs and weigh-below hook, larger more stable base, factory installed security built into base and...
SA-2019
Location: CBR Accessories
100 pack of coarse grade paper filter, used to separate spacer disc and soil in the CBR mold during compaction operation or over the top surface of the soil when the compaction operation is completed.
Tamping Rod 24" long x 5/8" dia.
CA-0400
Location: Parts & Accessories
Tamping Rods from Test Mark eliminate air voids in concrete when making slump tests, concrete cylinders or conducting concrete air entrainment test. Hemispherically rounded on both ends and plated for corrosion resistance.
(2) options
Location: Permeameters
The Compaction Permeameter from Test Mark is used for determining permeability of clay, sand and gravel soils using the Proctor plasticity compaction method.
Material Handling Pan, 15" x 30" x 4" deep (381 x 762 x 102mm)
CA-2480
Location: Parts & Accessories
Steel handling pans have a chute end and swing down handles to permit oven access. 15" by 13" by 4" deep model.
Material Handling Pan, 12" x 20.5" x 4" deep (305 x 521 x 102mm)
CA-2485
Location: Parts & Accessories
Steel handling pans have a chute end and swing down handles to permit oven access. 12" x 20.5" x 4" deep model.
