Product Search
Search results for 'D6931'
Showing 81 - 100 of 1123 Total Results
CA-2862
Location: Concrete
Special 3/4" orifice is used with thick grouts with efflux time of more than 35 seconds.
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers.. The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel with...
SA-0210
Location: Sand Density
The Density Plate provides a flat, stable base for the sand cone apparatus - available from Test Mark Industries.
(8) options
Location: Cylinder Molds - Plastic
Test Mark Industries features plastic concrete cylinder molds as part of a complete line of concrete testing equipment.
Spacers for CM-0030 and CM-2500 series
(4) options
Location: Spacers
Spacers are used with test platens to adjust the vertical working clearance height inside a machines load frame, for testing samples of various types and sizes to prevent over-extension of the load frames piston. They are manufactured from steel and machined plane on both ends to maintain a...
(4) options
Location: Retainers & Pads
Test Mark supplies grout sample unbonded capping system for compression testing of grout specimens in concrete testing environments.
Feeler Gauge Stock, .001 - 12"L x 1/2"W with rounded ends
CA-0481
Location: Parts & Accessories
When used with the steel parallel bar, Test Mark's feeler gauge stock will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
Sand Equivalent Shaker, Spring
CA-4055
Location: Sand Equivalent
The spring-type hand shaker from Test Mark Industries is more operator-dependent than the mechanical model.
Marshall Compaction Rotating Mold, 4"
AA-0046
Location: Marshall 4" Compaction Molds
Marshall Compaction Rotating Mold is used for preparing test specimens with rotating mold compactors - from Test Mark Industries.
CA-1310
Location: Hot Plates
These durable hotplates are equipped with thermostatic temperature control. Baffle-vented welded stainless-steel case and cast-aluminum top for maximum heat transfer, strength and corrosion resistance.
Spacers for CM-4000 and CM-5000 Series
(2) options
Location: Spacers
Spacer Assembly for Compresson Machines is used to adjust the inside vertical testing height of the compression machine load frame for testing samples of various heights.
CA-3125
Location: Vicat Apparatus
The Plastic Conical Mold from Test Mark is used with all Vicat Apparatus as part of a complete cement testing solution.
(2) options
Location: Flow Cones
The grout flow cone from Test Mark is used to determine the flow of grout mixtures by measuring the time of efflux of a specified volume of grout from a flow cone.
SA-1402
Location: Soils
Weights used to ensure uniform and repeatable weight is applied during testing for accurate readings.
SA-1120
Location: Manometer Tubes
The economical, wall mount Manometer Tube from Test Mark is built for use with many permeameters.
SA-1122
Location: Manometer Tubes
The economical free-standing Manometer Tube from Test Mark allows each tube to have its own valve to allow running two tests.
4" Test Cylinder Carrying Case
CA-0214
Location: Cylinder Transport
The test cylinder carrying case from Test Mark holds 8 - 4x8 test cyliners for easier field to lab transfer with less specimen damage.
CA-0355-SP
Location: Self-Consolidating Concrete
Test Mark's J-Ring Test Set is used to characterize the ability of self-consolidating concrete (SCC) to pass through reinforcing steel.
iD-Indicator
Location: Digital Load Indicating Systems
Dual operating language option – display all test setup menu programs in either English or Spanish., Automatically calculates and displays peak stress at the end of a test.. Digital display in English Digital display in Spanish The iD indicator is the system of choice for testing programs where...
