Product Search
Search results for 'C359'
Showing 101 - 120 of 1124 Total Results
Feeler Gauge Set, .002 to .025
CA-0485
Location: Planeness/Thickness Gauges
When used with the steel parallel bar, Test Mark's feeler gauge will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
CA-0280-P
Location: Cube Molds
The high-density polyethylene three-gang mold for 2-inch cubes strips and reassembles easily. Easy ordering online from Test Mark Industries.
CA-1420
Location: Bench Ovens
These bench ovens are used for curing, drying, baking. Ovens feature high density insulation for reduced heat loss and efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 7.0 cu. ft., 437ºF model.
Bench Oven, 10.6 cu. ft. 437ºF
CA-1440
Location: Bench Ovens
These bench ovens are used for curing, drying, and baking. Ovens feature high density insulation for reduced heat loss efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 10.6 cu. ft. model.
SA-0240
Location: Soil Pocket Penetrometer
The Soil Pocket Penetrometer from Test Mark is used for the evaluation and classification of cohesive soils in terms of soil consistency.
Feeler Gauge Stock, .001 - 12"L x 1/2"W with rounded ends
CA-0481
Location: Parts & Accessories
When used with the steel parallel bar, Test Mark's feeler gauge stock will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
(2) options
Location: Consistometer
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete - from Test Mark Industries.
Stainless Steel Clamp Assembly
CA-0600-07P
Location: Parts & Accessories
Stainless steel clamp assembly. Plastic Roll-A-Meter Kit replacement parts.
CA-2500
Location: Sample Splitters
The Test Mark mini sample splitter accurately divides dry materials, such as cement, powdered ores, coal, coke, sand, soils and other fine aggregates, so each half is representative of the original total sample.
SA-0112
Location: Asphalt
Mold Extractor is used with compression tester for removing 4" compaction mold specimens.
SA-0340
Location: Resiliency Tester
The Resiliency Tester is used to test resiliency of hard rubber base of liquid limit machines, which should be done at 90-day intervals to ensure base is in compliance with ASTM Standards.
CA-2670
Location: Specific Gravity Flasks
The le chatelier flask from Test Mark is used to determine the relative density of cement or sand and other fine materials.
AA-0040-A
Location: Marshall Testing
Set includes Hand Compaction Hammer, 4" Compaction Mold, Compaction Pedestal with Top Plate, Hammer Support Rod with Adjustable Guide and Compaction Mold Holder.
CA-2562
Location: Aggregate
The chute attachment replaces one pan to permit loading of material directly into a bag or container.
Aquaprobe™ Soil Moisture Meter
(2) options
Location: Soil Moisture Meters
Aquaprobe from Test Mark can determine the soil moisture content of different types of soils and other fine aggregate.
(2) options
Location: 6" Cube Mold
This single cavity cube mold with base plate is used for compression testing of concrete cubes or mortar samples in the "Time of Initial" and "Final Setting" of concrete. Dimensions: 6" x 6" x 6" (152 x 152 x 152 mm).
TM-2270
Location: Digital Load Indicating Systems
The new TM-2270 is an easy-to-use economical Digital Load Indicator loaded with features found in more expensive units.
