Product Search
Search results for 'T245'
Showing 101 - 120 of 1648 Total Results
Vapor Emission Test Kit, 3 per pkg.
CA-2594
Location: Parts & Accessories
The vapor emission test method is specified by the Floor Covering Industry as the primary measure of moisture acceptable for floor covering or coating installations. Product has three per package.
CA-4052
Location: Sand Equivalent
The mechanical motor-driven sand equivalent shaker from Test Mark is recommended for performing sand equivalent tests on a regular basis.
CA-0500
Location: Air Entrainment/Pressure Meter
The air entrainment concrete pressure meter from Test Mark is part of a complete line of concrete testing equipment, available for easy online ordering.
Test Mark Industries supplies calibration and service locations for its construction testing equipment.
Constant/Falling Head Permeameter Set, 2.5" (63.4 mm)
SA-2200
Location: Parts & Accessories
Constant/Falling Head Permeameter Set for use with granular soils in determining the coefficient of permeability via the constant or falling-head method for laminar flow of water. Funnel provides adjustable constant head reservoir. Top cap applies 5-10 lbs. of force against top stone or screen to...
CA-3020-M
Location: Flow Tables
Cast bronze cone mold 70 mm top dia. x 50 mm high x 100 mm bottom dia.
CA-0212
Location: Cylinder Transport
Sample cart is painted steel with two shelves. Overall dimensions 34" x 17" x 31 ½" (864 x 432 x 800 mm). Load capacity is 400 lbs. (181 kg). Ships unassembled.
(4) options
Location: Tamping Rods for Concrete
Tamping rods from Test Mark eliminate air voids in concrete when making slump tests, concrete cylinders or conducting concrete air entrainment test.
6" ( 152 mm) Cube Mold, Single
CA-0275
Location: Parts & Accessories
The single cavity cube mold from Test Mark is used for compression testing of concrete cubes or mortar samples.
(2) options
Location: Compaction Hammers
Soil Compaction Hammers from Test Mark are machined from steel and plated for rust resistance. Easy online ordering.
Test Mark Industries is a manufacturer and supplier of construction materials testing equipment used for testing concrete, cement, aggregates, asphalt and soil samples to ASTM and AASHTO standards.
CA-0120
Location: Parts & Accessories
These heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder. Place cylinders against adjustable guides on vertical arms for precise...
3" x 6" & 2" x 4" Vertical Capper
CA-0130
Location: Parts & Accessories
These heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder. Place cylinders against adjustable guides on vertical arms for precise...
Muffle Furnace 4 1/4" x 5" x 6"
CA-1480
Location: Muffle Furnace
Test Mark's small bench-top muffle furnace features heating elements on top and side to provide uniform temperature.
CA-1485
Location: Muffle Furnace
Test Mark's small bench-top muffle furnace features heating elements on top and side provide uniform temperature.
Sand Equivalent Shaker, Spring
CA-4055
Location: Sand Equivalent
The spring-type hand shaker from Test Mark Industries is more operator-dependent than the mechanical model.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
Perpendicular Verification Device, 6" x 12" Cylinders
CA-0295
Location: Parts & Accessories
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
CA-0241
Location: Parts & Accessories
Dial caliper features a 6" measuring range with .001" graduations and .100" per revolution. Hardened and ground stainless steel main beam with hardened, ground and lapped measuring faces. Jaw depth is 1.5".
