Product Search
Search results for 'D-560'
Showing 121 - 140 of 1124 Total Results
AA-2055
Location: Vacuum Extractor
Vacuum Extractor from Test Mark is used for quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples.
Liquid Limit (w/counter) Test Set
SA-0310-S
Location: Liquid Limit Test Sets
Liquid limit test sets with counters are available as part of complete line of soil testing products from Test Mark Industries.
CA-2950-D
Location: Comparator, Length Change
The Digital Comparator from Test Mark measures length changes of hardened cement paste, mortar, and concrete prismatic specimens.
(4) options
Location: Cylinder Molds - Steel
Test Mark Industries features steel concrete cylinder molds as part of a complete line of concrete testing equipment.
Aqua-Check Kit, 20 gram capacity
SA-0255
Location: Moisture Testing
The Aqua-Check from Test Mark is a portable system used for measuring the moisture content of a wide range of materials including sand, aggregates and soil.
CA-0952
Location: Test Hammer (Rebound)
The easy-to-use concrete test hammer from Test Mark gives consistent concrete strength test estimates within a range of 1,500 to 8,000 psi.
CA-0280-P
Location: Cube Molds
The high-density polyethylene three-gang mold for 2-inch cubes strips and reassembles easily. Easy ordering online from Test Mark Industries.
AA-2000
Location: Reflux Extractor
The Reflux Extractor Set from Test Mark, used for asphalt testing, features 2 cones, each with a 1000g capacity.
Pad Caps and Retainer Rings - Steel
(16) options
Location: Unbonded Capping (Retainers and Pad Caps)
Pad caps and retainer rings are available from Test Mark as part of a complete line of concrete testing equipment and supplies.
(2) options
Location: Trowels
Test Mark's strike-off trowels are used to strike off and smooth excess concrete and grout from the surface of molds.
CA-0600-05P
Location: Parts & Accessories
Meter bottom base. Plastic Roll-A-Meter Kit replacement parts.
(2) options
Location: Permeameters
The Compaction Permeameter from Test Mark is used for determining permeability of clay, sand and gravel soils using the Proctor plasticity compaction method.
SA-1402
Location: Soils
Weights used to ensure uniform and repeatable weight is applied during testing for accurate readings.
AA-0120
Location: Drierite
Easily installs in-line between vacuum pump and rice test equipment. Refillable unit measures 2 5/8" by 11 3/8" with hose barbs at both ends which will accept ΒΌ" to 3/8' flexible tubing. One of our Drierite products.
Speedy 2000 Moisture Tester 20 gr.
SA-0250
Location: Moisture Testing
The Speedy 2000 Moisture Tester from Test Mark is widely accepted for determining the free moisture content of a variety of materials - sand, aggregates, soil and other powders.
AA-0015
Location: Marshall Basic Compression Testing
The dial indicator consists of a maximum position brake assembly and guide sleeve. Accommodates 4" or 6" breaking heads. Graduations of 0.01" div., range 1.00"...
CA-0500-42
Location: Air Meter Calibrators
Brass reusable calibration vessel can be used with any 1/4 cu. ft. concrete pressure meter. Vessel is exactly 5% air by volume when placed in the pressure meter base. Part of our air meter calibrator products.
(3) options
Location: Round Pans/Mixing Bowl
Test Mark supplies round pans and mixing bowls for laboratory use in materials testing applications.
SA-0210
Location: Sand Density
The Density Plate provides a flat, stable base for the sand cone apparatus - available from Test Mark Industries.
CA-0851
Location: Cement
Penetrometer Foot is a stainless steel disk, 2.70" (68.58 mm) dia. for use with masonry mortars to determine board life and initial consistency.