Product Search
Search results for 'D-422'
Showing 241 - 260 of 1124 Total Results
(8) options
Location: Cylinder Molds - Plastic
Test Mark Industries features plastic concrete cylinder molds as part of a complete line of concrete testing equipment.
SA-2032
Location: CBR Accessories
Machined from seamless tubing with a sharpened edge to enable undisturbed samples to be taken in the field, cutting edge is plated for rust resistance. Recess in upper section allows edge to be mounted at either end of the mold to facilitate sample removal in the field.
Drive Tubes, 3" x 2.75" (76.2 x 69.9 mm), 10/pkg
SA-1371
Location: Density Drive Sampler
For use with Drive Sampler, 3" (76.2mm) x 2.75" (69.9mm) length, (3" x 0.01 ft3). Accessory to the density drive sampler.
Drive Tubes, 4" x 5.00" (101.6 x 127 mm), 10/pkg
SA-1372
Location: Density Drive Sampler
For use with Drive Sampler, 4" (101.6mm) x 5" (127mm) length, (4" x 0.033 ft3).
CA-0500-42
Location: Air Meter Calibrators
Brass reusable calibration vessel can be used with any 1/4 cu. ft. concrete pressure meter. Vessel is exactly 5% air by volume when placed in the pressure meter base. Part of our air meter calibrator products.
CA-0236
Location: Micrometer
This concrete micrometer was designed to accurately measure the diameter of concrete cylinders with a range of 5.5 - 6.5in.
(2) options
Location: Proctor Molds
Proctor molds from Test Mark are manufactured from steel with all parts plated for longer life.
(3) options
Location: Test Platens
Used for testing 6” (152 mm) concrete cubes and cylinders in compression . The platens bearing block is 6.5” (152 mm) square, through hardened to HRC 55 or greater, plane to .0005” (.012 mm) in any 6” (152 mm) area, has concentric circles for easier centering of cylinders and is hard nickel plated...
SA-0354-S
Location: Shrinkage Limit Set
The Shrinkage Limit Set from Test Mark is part of a complete line of soil testing equipment. Easy online ordering.
CA-0286
Location: Cube Molds
The 2-inch cube maker molding system from Test Mark uses watertight polypropylene liners which fit into a 3-gang metal mold frame.
Marshall Compaction Stationary Mold, 4"
AA-0045
Location: Marshall 4" Compaction Molds
Marshall Compaction Stationary Mold is for hand and non-rotating base compactors and is machined from seamless tubing and plated - from Test Mark Industries.
(3) options
Location: Wash Bottles
Test Mark Industries supplies wash bottles as part of a complete line of soil testing equipment and supplies.
Curing Rack, 4" x 8" Cylinders 6/ctn
CA-0218
Location: Parts & Accessories
These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water...
Curing Rack, 4" x 8" Cylinders 12/ctn
CA-0219
Location: Parts & Accessories
These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water...
(2) options
Location: Proctor Molds, split
Split proctor molds from Test Mark are manufactured from steel with all parts plated for longer life.
Wire Cloth Field Rocker Screen Set
CA-1570
Location: Field Rocker Screen Set
The field rocker screen set from Test Mark Industries consists of a 12-inch square steel frame with interchangeable wire cloth and bottom pan.
(6) options
Location: Sample Tins
Test Mark Industries supplies sample tins as part of a complete line of soil testing equipment.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
