Product Search
Search results for 'C-805'
Showing 41 - 60 of 1648 Total Results
Portable Precision Balance, 6000 g x 0.1 g
SC-0195
Location: Parts & Accessories
The Portable Precision Balance from Test Mark features selectable weighing units, percentage weighing and below balance weighing functions, stainless steel pan, adjustable feet, low battery indicator and auto-power shut off, manual internal calibration with built in mass, RS-232 and USB interface,...
CA-0500-11
Location: Parts & Accessories
Pump plunger o-ring. Pressure meter replacement parts; Test Mark Industries.
6.5" dia. x 1" Thick Lower Platen
MA-0600
Location: Parts & Accessories
6.5" dia. x 1" Thick Platen.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
Aquaprobe™ Soil Moisture Meter
(2) options
Location: Soil Moisture Meters
Aquaprobe from Test Mark can determine the soil moisture content of different types of soils and other fine aggregate.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
Perpendicular Verification Device, 6" x 12" Cylinders
CA-0295
Location: Parts & Accessories
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
SA-0280
Location: Parts & Accessories
The Aquaprobe™ can determine the soil moisture content of different types of soils and other fine aggregate. Simply insert the five prongs in the soil to be measured and review the percentage moisture on display. A special guide is supplied to assist the user with inserting the prongs in...
Fresh Concrete Field Testing Kits, 6" x 12"
CA-0510
Location: Fresh Concrete Field Testing
Fresh concrete kits contain everythiung you need for routine testing of fresh concrete testing in the field, with all items meeting ASTM standards.
Fresh Concrete Field Testing Kits, 4" x 8"
CA-0515
Location: Fresh Concrete Field Testing
Fresh concrete kit (4" x 8") contains everything you need for routine testing of fresh concrete testing in the field, with all items meeting ASTM standards.
Digital Manometer, NIST Certified
AA-0073-T
Location: Parts & Accessories
Features a digital display with a range of 0 to 1000 mm Hg. Includes a ten-point NIST traceable certificate of calibration.
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
CA-0234
Location: Parts & Accessories
Cylinder wraps are made of canvas nylon with velcro strips. Use these wraps around your concrete test cylinder to help minimize debris from shattering during compression testing. Product is 4" by 8".
CA-0235
Location: Parts & Accessories
Cylinder wraps are made of canvas nylon with velcro strips. Use these wraps around your concrete test cylinder to help minimize debris from shattering during compression testing. Product is 6" by 12".
(3) options
Location: Vertical Cappers
Test Mark's heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder.
CA-2050
Location: Sieve Brushes
The Wire Sieve Brush from Test mark features a steel wire with loop handle for cleaning coarse series sieves.
CA-0500-9V
Location: Parts & Accessories
Brass pump check valve. Pressure meter replacement parts; Test Mark Industries.
CA-0500-9VP
Location: Parts & Accessories
Plastic pump check valve. Pressure meter replacement parts; Test Mark Industries.
(5) options
Location: Unit Weight Buckets
Aluminum cylindrical unit weight measures from Test Mark have machined interior surfaces, carrying handles, true and even top and bottom surfaces, are water-tight and will retain form after repeated use.
CA-0300
Location: Parts & Accessories
Lightweight steel beam molds are used for molding third or center point test samples. Molds are hinge free to collapse into interchangeable parts for easy stripping, cleaning and quick reassembly with wing nuts.
