Product Search
Search results for 'T158'
Showing 61 - 80 of 1124 Total Results
CA-0356-P
Location: Concrete
Plastic base plate with convenient cut-out carrying handles and inscribed with concentric circles. Dimensions 36" x 36" x 1/2".
CA-0600-05P
Location: Parts & Accessories
Meter bottom base. Plastic Roll-A-Meter Kit replacement parts.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
CA-0364
Location: Slump Testing
K-Slump Tester for in-place measurements indicates correlation to the slump test. The probe determines workability of concrete and the degree of compaction.
Cylinder Platen, 6 ½” Diameter
(3) options
Location: Test Platens
Free floating bearing platen seats under test pressure.. Used when testing 6” (152 mm) or 4” (101 mm) diameter concrete cylinders in compression. Platen is manufactured from steel with all components plated for corrosion resistance. Upper cylinder platen used when testing 6” (152 mm) or 4” (101 mm)...
CA-0789
Location: Min/Max Thermometers
Test Mark's min-max thermometer indicates present temperature and the highest/lowest temperatures since last reset.
Long Stem Digital, NIST Traceable
CA-0785-T
Location: Digital Long Stem, Traceable
Long Stem Digital Thermometer, NIST Traceable.
Wire Cloth Field Rocker Screen Set
CA-1570
Location: Field Rocker Screen Set
The field rocker screen set from Test Mark Industries consists of a 12-inch square steel frame with interchangeable wire cloth and bottom pan.
CA-3032
Location: Flow Tables
Measure is calibrated to 400 ml and is used to determine air content of hydraulic cement mortar. Cylindrical measure is 3" (76 mm) ID and approximately 3 15/32" (88 mm) deep.
CA-0600-08P
Location: Parts & Accessories
Plastic Case for Volumetair Meter. Plastic Roll-A-Meter Kit replacement parts.
CA-2950-D
Location: Comparator, Length Change
The Digital Comparator from Test Mark measures length changes of hardened cement paste, mortar, and concrete prismatic specimens.
SA-0340
Location: Resiliency Tester
The Resiliency Tester is used to test resiliency of hard rubber base of liquid limit machines, which should be done at 90-day intervals to ensure base is in compliance with ASTM Standards.
CA-0358
Location: Self-Consolidating Concrete
The V-Funnel is used to measure flowability of fresh self-consolidating concrete. The funnel is filled and the time taken for it to flow through the apparatus is measured. A valve on the outflow port can be closed to allow SCC to settle, which indicates the tendency for segregation.
SA-0362
Location: Plastic Limit
Test Mark's Plastic Limit Roller for soils is a unique time-saving device designed to produce consistent results by an easily repeatable mechanical technique.
(5) options
Location: Prism Molds
1 Gang Molds from Test Mark are designed to produce the required 10-inch gauge length prism molds. Easy and secure ordering online.
SA-3500
Location: Mud Balance Testing
Mud Balances are used as standard procedure instruments for testing water and oil-base drilling fluids and oil well cements.
SA-0200
Location: Sand Density
The Sand Cone Density Apparatus from Test Mark Industries determines the in-place density of soils.
CA-0245
Location: Vibrator
The lightweight electric concrete vibrator from Test Mark vibrates concrete test cylinders and molds in the laboratory or field.
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders.. The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of test...
(2) options
Location: Flow Cones
The grout flow cone from Test Mark is used to determine the flow of grout mixtures by measuring the time of efflux of a specified volume of grout from a flow cone.
