Product Search
Search results for 'T283'
Showing 101 - 120 of 1647 Total Results
CA-0970
Location: Test Hammer (Rebound)
The calibration test anvil from Test Mark Industries is used to check the calibration accuracy of a test hammer.
CA-2980
Location: Organic Impurities
The Organic Impurities Test Set from Test Mark determines the presence of injurious organic compounds in sand used in mortar or cement.
SA-1050
Location: Dispersion Mixer
Test Mark's soil mixer is for dispersing solid suspensions used in hydrometer method of testing sub-grade soils.
CA-0120
Location: Parts & Accessories
These heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder. Place cylinders against adjustable guides on vertical arms for precise...
3" x 6" & 2" x 4" Vertical Capper
CA-0130
Location: Parts & Accessories
These heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder. Place cylinders against adjustable guides on vertical arms for precise...
CA-1420
Location: Bench Ovens
These bench ovens are used for curing, drying, baking. Ovens feature high density insulation for reduced heat loss and efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 7.0 cu. ft., 437ºF model.
CA-1430
Location: Bench Ovens
These bench ovens are used for curing, drying, and baking. Ovens feature high density insulation for reduced heat loss and efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 7.0 cu. ft., 300ºF model.
Bench Oven, 10.6 cu. ft. 437ºF
CA-1440
Location: Bench Ovens
These bench ovens are used for curing, drying, and baking. Ovens feature high density insulation for reduced heat loss efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 10.6 cu. ft. model.
(3) options
Location: Liquid Limit Testing Machines
Liquid limit machines from Test Mark are part of a complete line of soil testing equipment and supplies.
CA-3010
Location: Flow Tables
Motorized flow tables from Test Mark Industries are used to determine consistency of cement mortars. Features a 10-inch dia. cast bronze table.
CA-2861
Location: Concrete
1/2" ID discharge tube orifice is used with grouts having 35 seconds or less efflux time.
CA-2862
Location: Concrete
Special 3/4" orifice is used with thick grouts with efflux time of more than 35 seconds.
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers.. The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel with...
SA-0210
Location: Sand Density
The Density Plate provides a flat, stable base for the sand cone apparatus - available from Test Mark Industries.
(4) options
Location: Test Platens
Models available for testing up to 12” (305 mm) CMUs.. All models feature large diameter spherical disk and seat assemblies, and platen bearing surface plane to .001” (.025 mm) in any 6” (152 mm) direction, through hardened to HRC 60 and plated for wear and corrosion resistance. The bearing block...
(8) options
Location: Cylinder Molds - Plastic
Test Mark Industries features plastic concrete cylinder molds as part of a complete line of concrete testing equipment.
Spacers for CM-0030 and CM-2500 series
(4) options
Location: Spacers
Spacers are used with test platens to adjust the vertical working clearance height inside a machines load frame, for testing samples of various types and sizes to prevent over-extension of the load frames piston. They are manufactured from steel and machined plane on both ends to maintain a...
(4) options
Location: Retainers & Pads
Test Mark supplies grout sample unbonded capping system for compression testing of grout specimens in concrete testing environments.
Feeler Gauge Stock, .001 - 12"L x 1/2"W with rounded ends
CA-0481
Location: Parts & Accessories
When used with the steel parallel bar, Test Mark's feeler gauge stock will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
6" x 12" (152 x 305 mm) Plastic Mold with Lip, 20/ctn
CA-0206
Location: Parts & Accessories
Plastic molds from Test Mark are injected plastic for close tolerances and consistency of shape. Easy online ordering.
