Product Search
Search results for 'D-6926'
Showing 121 - 140 of 1123 Total Results
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders. . The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of...
AA-2055
Location: Vacuum Extractor
Vacuum Extractor from Test Mark is used for quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples.
AA-0095
Location: Vacuum Pump
Direct-drive, two-stage, rotary-sliding, vane-high vacuum pump features a gas ballast and trap to reduce risk of oil being sucked into the system.
CA-3020-M
Location: Flow Tables
Cast bronze cone mold 70 mm top dia. x 50 mm high x 100 mm bottom dia.
Plastic Tamping Rod 5/8" x 12"
CA-0600-09P
Location: Parts & Accessories
Plastic Tamping Rod 5/8" x 12". Plastic Roll-A-Meter Kit replacement parts.
(2) options
Location: 6" Cube Mold
This single cavity cube mold with base plate is used for compression testing of concrete cubes or mortar samples in the "Time of Initial" and "Final Setting" of concrete. Dimensions: 6" x 6" x 6" (152 x 152 x 152 mm).
SA-0113
Location: Sample Ejector
The Soil Sample Ejector from Test Mark is used for removing soil samples from molds up to 7 in. long and 2, 3 and 4 in. dia. Shelby Tubes.
CA-0361-S
Location: Slump Testing
Test Mark's portable slump test sets consist of a steel slump cone, tamping rod, cast-aluminum test base with handle for easy transportation and round mouth scoop.
(4) options
Location: Manual Compression Testing Machines
Testing range of 5,000 to 500,000 lbs. (22.2 – 2,224 kN) with an accuracy of ±.5% of indicated load., Frame stiffness rating of 41.6 million lbs/in., Easier specimen loading with large platen table. . Request a Quote Our CM-5000 series machines feature rigid distortion-resistant load frames...
Speedy 2000 Moisture Tester 20 gr.
SA-0250
Location: Moisture Testing
The Speedy 2000 Moisture Tester from Test Mark is widely accepted for determining the free moisture content of a variety of materials - sand, aggregates, soil and other powders.
CA-2980
Location: Organic Impurities
The Organic Impurities Test Set from Test Mark determines the presence of injurious organic compounds in sand used in mortar or cement.
CA-4052
Location: Sand Equivalent
The mechanical motor-driven sand equivalent shaker from Test Mark is recommended for performing sand equivalent tests on a regular basis.
Spacers for CM-0030 and CM-2500 series
(4) options
Location: Spacers
Spacers are used with test platens to adjust the vertical working clearance height inside a machines load frame, for testing samples of various types and sizes to prevent over-extension of the load frames piston. They are manufactured from steel and machined plane on both ends to maintain a...
Digital Static Cone Penetrometer
SA-1510
Location: Static Cone Penetrometer
Digital Static Cone Penetrometer from Test Mark features a large digital readout making testing and recording readings easy.
Density Drive Sampler, 3" ( 76.2 mm)
SA-1355
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 3" model.
Excel Clean HD Biodegradable Extraction Solvents
(2) options
Location: Biodegradable Extraction Solvents
Excel Clean HD Biodegradable Extraction Solvent is approved by many state DOTs for centrifugal and vacuum asphalt extraction tests.
CA-2950-D
Location: Comparator, Length Change
The Digital Comparator from Test Mark measures length changes of hardened cement paste, mortar, and concrete prismatic specimens.
SA-2015
Location: CBR Accessories
Disc is used as a false bottom in a soil mold during the compaction process. Plated rust-resistant steel disc is 2.416" (61mm) high, 5-15/16" (150.8mm) dia.
SA-2015-L
Location: CBR Accessories
Disc is used as a false bottom in a soil mold during the compaction process. Plated rust-resistant steel disc is 1.416" (36mm) high, 5-15/16" (150.8mm) dia.
