Product Search
Search results for 'D-427'
Showing 241 - 260 of 1124 Total Results
MA-1101
Location: Machine Accessory Lift
The machine accessory lift can raise 1,100 pounds easily with a detachable metal handle - changing out breaking heads or adding spacers is quick and easy.
SA-2015
Location: CBR Accessories
Disc is used as a false bottom in a soil mold during the compaction process. Plated rust-resistant steel disc is 2.416" (61mm) high, 5-15/16" (150.8mm) dia.
SA-2015-L
Location: CBR Accessories
Disc is used as a false bottom in a soil mold during the compaction process. Plated rust-resistant steel disc is 1.416" (36mm) high, 5-15/16" (150.8mm) dia.
CA-2965
Location: Comparator, Length Change
Gauge studs have stainless steel contact points for use with prism molds. Sold 10 per package. Part of our comparator/length change products.
(2) options
Location: Sample Bags
Plastic-lined sample bags from Test Mark are used to transport soils, cement, aggregate, and wet materials from the field to the laboratory.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
Circulating Water Bath, Digital
AA-0065
Location: Circulating Water Bath
The circulating water bath from Test Mark is fully insulated with magnetic circulator for heating up to 12 4-inch diameter Marshall samples at a time.
CA-0970
Location: Test Hammer (Rebound)
The calibration test anvil from Test Mark Industries is used to check the calibration accuracy of a test hammer.
SA-0245
Location: Shear Vane Tester
The pocket shear vane tester from Test Mark provides a quick and efficient method for determining shear strength values of cohesionless values of soils.
(2) options
Location: Rebar Locator
Test Mark's Rebarscope™ locates reinforcement bars in concrete and determines their depth and size.
SA-2000
Location: CBR Load Frames
The CBR (California Bearing Ratio) loading press from Test Mark uses a two-position mechanical jack to provide steady test speeds, as well as rapid travel of the platen for positioning of the sample.
CA-3010
Location: Flow Tables
Motorized flow tables from Test Mark Industries are used to determine consistency of cement mortars. Features a 10-inch dia. cast bronze table.
SA-0665
Location: Hydrometer Jar Bath
Hydrometer Jar Bath from Test Mark Industries holds up to eight hydrometer jars at the same time.
(2) options
Location: 6" Cube Mold
This single cavity cube mold with base plate is used for compression testing of concrete cubes or mortar samples in the "Time of Initial" and "Final Setting" of concrete. Dimensions: 6" x 6" x 6" (152 x 152 x 152 mm).
Concrete Cylinder Length Measuring Device for 4 & 6''Dia-24''L
CA-0237
Location: Core Length
With the core length measuring device measurements can be taken at the center point of the sample's upper end as well as the 8 equidistant points along the circumference.
SA-0220
Location: Sand Density
Density Sand is used with the sand density apparatus to determine the bulk density of soil.
Speedy Moisture Reagent, 10 lb. can
SA-0262
Location: Soils
Calcium Carbide Reagent is used with the Speedy Moisture Tester to create pressure proportional to moisture in test samples. Supplied in 10-lb. can.
CA-0500-42
Location: Air Meter Calibrators
Brass reusable calibration vessel can be used with any 1/4 cu. ft. concrete pressure meter. Vessel is exactly 5% air by volume when placed in the pressure meter base. Part of our air meter calibrator products.
(2) options
Location: Flow Cones
The grout flow cone from Test Mark is used to determine the flow of grout mixtures by measuring the time of efflux of a specified volume of grout from a flow cone.
CA-2560
Location: Sample Splitters
The adjustable sample splitter from Test Mark reduces aggregates to a suitable size and amount for gradation testing.
