Product Search
Search results for 'T-283'
Showing 41 - 60 of 1123 Total Results
CA-2720
Location: Specific Gravity & Absorption Fine Aggregates
The conical mold and tamper from Test Mark are used to determine bulk and apparent specific gravity and absorption of fine aggregate.
CA-2500
Location: Sample Splitters
The Test Mark mini sample splitter accurately divides dry materials, such as cement, powdered ores, coal, coke, sand, soils and other fine aggregates, so each half is representative of the original total sample.
CA-0933
Location: Specimen Curing
The curing tank immersion heater from Test Mark has an adjustable thermostat and a 1,000 watt 15 amp incolloy shielded heating element that resists rust.
(3) options
Location: Aggregate Washers
Aggregate samples are automatically washed with Test Mark's aggregate washers to remove clay and other fines passing a No. 200 sieve.
(4) options
Location: Moisture Boxes
Test Mark provides aluminum moisture boxes that protect the sample from exposure during weighing operations.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
CA-1430
Location: Bench Ovens
These bench ovens are used for curing, drying, and baking. Ovens feature high density insulation for reduced heat loss and efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 7.0 cu. ft., 300ºF model.
CA-0970
Location: Test Hammer (Rebound)
The calibration test anvil from Test Mark Industries is used to check the calibration accuracy of a test hammer.
CA-1420
Location: Bench Ovens
These bench ovens are used for curing, drying, baking. Ovens feature high density insulation for reduced heat loss and efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 7.0 cu. ft., 437ºF model.
CA-0793
Location: Min/Max Thermometers
Eliminates all of the problems associated with mercury separation and air bubbles trapped in traditional thermometers. Weather resistant rugged plastic case for outdoor use. Displays three independent temperature readings of current, maximum and minimum since last reset.
TM-2270
Location: Digital Load Indicating Systems
The new TM-2270 is an easy-to-use economical Digital Load Indicator loaded with features found in more expensive units.
Drierite Dessicant, 1 lb. white
AA-0124
Location: Drierite
Protects vacuum pump by removing final trace of moisture. Must be used with blue indicating drierite.
Fresh Concrete Field Testing Kits, 6" x 12"
CA-0510
Location: Fresh Concrete Field Testing
Fresh concrete kits contain everythiung you need for routine testing of fresh concrete testing in the field, with all items meeting ASTM standards.
Fresh Concrete Field Testing Kits, 4" x 8"
CA-0515
Location: Fresh Concrete Field Testing
Fresh concrete kit (4" x 8") contains everything you need for routine testing of fresh concrete testing in the field, with all items meeting ASTM standards.
SA-3500
Location: Mud Balance Testing
Mud Balances are used as standard procedure instruments for testing water and oil-base drilling fluids and oil well cements.
CA-2585
Location: Rebar Electronic Metal Detector
Test Mark's hand-held electronic metal detector locates rebars, metal pipe and conduit through concrete up to depths of 6 inches.
Drive Tubes, 3" x 2.75" (76.2 x 69.9 mm), 10/pkg
SA-1371
Location: Density Drive Sampler
For use with Drive Sampler, 3" (76.2mm) x 2.75" (69.9mm) length, (3" x 0.01 ft3). Accessory to the density drive sampler.
