Product Search
Search results for 'T245'
Showing 41 - 60 of 1648 Total Results
SA-0245
Location: Shear Vane Tester
The pocket shear vane tester from Test Mark provides a quick and efficient method for determining shear strength values of cohesionless values of soils.
Spacers for CM-4000 and CM-5000 Series
(2) options
Location: Spacers
Spacer Assembly for Compresson Machines is used to adjust the inside vertical testing height of the compression machine load frame for testing samples of various heights.
(2) options
Location: Flow Cones
The grout flow cone from Test Mark is used to determine the flow of grout mixtures by measuring the time of efflux of a specified volume of grout from a flow cone.
CA-2180
Location: Parts & Accessories
Aggregate samples are automatically washed to remove clay and other fines passing a No. 200 sieve. Inconsistencies and the high cost of manual methods are eliminated.
CA-4000
Location: Windsor Probe
The Windsor Probe from Test Mark evaluates the compressive strength of in-place concrete. Easy online ordering.
Pad Caps and Retainer Rings - Steel
(16) options
Location: Unbonded Capping (Retainers and Pad Caps)
Pad caps and retainer rings are available from Test Mark as part of a complete line of concrete testing equipment and supplies.
(3) options
Location: Aggregate Washers
Aggregate samples are automatically washed with Test Mark's aggregate washers to remove clay and other fines passing a No. 200 sieve.
(3) options
Location: Spacers
Spacers are used to adjust the vertical testing height inside compression testing machine load frames when testing samples of various heights. Spacer mounts to the top cross head of the load frame. Spacer is manufactured from steel and is precision ground on both ends and painted for rust...
SA-0112
Location: Asphalt
Mold Extractor is used with compression tester for removing 4" compaction mold specimens.
AA-2055
Location: Vacuum Extractor
Vacuum Extractor from Test Mark is used for quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples.
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers.. The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel with...
CA-0280-P
Location: Cube Molds
The high-density polyethylene three-gang mold for 2-inch cubes strips and reassembles easily. Easy ordering online from Test Mark Industries.
CA-0933
Location: Specimen Curing
The curing tank immersion heater from Test Mark has an adjustable thermostat and a 1,000 watt 15 amp incolloy shielded heating element that resists rust.
30 Gallon Water Tank - 24" x 18" x 18" deep (620 x 457 x 457 mm). Max. Oper. Temp. - 140°F (60°C)
CA-2742
Location: Parts & Accessories
Seamless, translucent tanks are ¼" (6.4 mm) thick with a drain faucet and overflow outlet. 30 Gallon (114L) tank is 24" x 18" x 18" deep (610 x 457 x 457 mm). Maximum operating temperature is 140°F (60° C).
Constant/Falling Head Permeameter Set
(5) options
Location: Permeameter Sets
Constant/Falling Head Permeameter Set for use with granular soils in determining the coefficient of permeability via the constant or falling-head method for laminar flow of water.
Cylinder Platen, 6 ½” Diameter
(3) options
Location: Test Platens
Free floating bearing platen seats under test pressure.. Used when testing 6” (152 mm) or 4” (101 mm) diameter concrete cylinders in compression. Platen is manufactured from steel with all components plated for corrosion resistance. Upper cylinder platen used when testing 6” (152 mm) or 4” (101 mm)...
Speedy 2000 Moisture Tester 20 gr.
SA-0250
Location: Moisture Testing
The Speedy 2000 Moisture Tester from Test Mark is widely accepted for determining the free moisture content of a variety of materials - sand, aggregates, soil and other powders.
CA-0191
Location: Parts & Accessories
Our pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set. These neoprene pad inserts are made from a tough...
