Product Search
Search results for 'D-1557'
Showing 61 - 80 of 1123 Total Results
SA-2015
Location: CBR Accessories
Disc is used as a false bottom in a soil mold during the compaction process. Plated rust-resistant steel disc is 2.416" (61mm) high, 5-15/16" (150.8mm) dia.
SA-2015-L
Location: CBR Accessories
Disc is used as a false bottom in a soil mold during the compaction process. Plated rust-resistant steel disc is 1.416" (36mm) high, 5-15/16" (150.8mm) dia.
Stripping Tool, Aluminum Handle
CA-0240-A
Location: Stripping Tool
The durable stripping tool has a large easy-grip aluminum handle and a steel shaft. Quickly remove concrete specimens from single use plastic cylinder molds.
SA-2000
Location: CBR Load Frames
The CBR (California Bearing Ratio) loading press from Test Mark uses a two-position mechanical jack to provide steady test speeds, as well as rapid travel of the platen for positioning of the sample.
CA-1485
Location: Muffle Furnace
Test Mark's small bench-top muffle furnace features heating elements on top and side provide uniform temperature.
Circulating Water Bath, Digital
AA-0065
Location: Circulating Water Bath
The circulating water bath from Test Mark is fully insulated with magnetic circulator for heating up to 12 4-inch diameter Marshall samples at a time.
CA-1508
Location: Shakers, Economy
Test Mark provides basic sieve shakers for 8-inch sieves. Easy online ordering.
Blaine Air Permeability Apparatus
CA-2970
Location: Blaine Air Permeability
The Blaine Air Permeability Apparatus from Test Mark determines the fineness of Portland cement on terms of specific surface expressed as total surface area in square centimeters per gram of cement.
Mortar Penetration Resistance Apparatus
CA-2830
Location: Mortar Penetration Resistance
The mortar penetration resistance apparatus from Test Mark Industries determines the time of setting of concrete by penetration resistance.
(41) options
Location: Air Meter Replacement Parts
Concrete air/pressure meter replacement parts are available from Test Mark. Use our diagram to find the part you need for easy online ordering.
Cylinder Platen, 6 ½” Diameter
(3) options
Location: Test Platens
Free floating bearing platen seats under test pressure. . Used when testing 6” (152 mm) or 4” (101 mm) diameter concrete cylinders in compression. Platen is manufactured from steel with all components plated for corrosion resistance. Upper cylinder platen used when testing 6” (152 mm) or 4” (101...
CA-0933
Location: Specimen Curing
The curing tank immersion heater from Test Mark has an adjustable thermostat and a 1,000 watt 15 amp incolloy shielded heating element that resists rust.
Location: Soils
Test Mark's COE Manual Compaction Hammer features a recoil mechanism in the foot assembly to reduce impact fatigue.
Sand Equivalent Shaker, Spring
CA-4055
Location: Sand Equivalent
The spring-type hand shaker from Test Mark Industries is more operator-dependent than the mechanical model.
(2) options
Location: Consistometer
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete - from Test Mark Industries.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
Curing Rack, 4" x 8" Cylinders 6/ctn
CA-0218
Location: Parts & Accessories
These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water...
Curing Rack, 4" x 8" Cylinders 12/ctn
CA-0219
Location: Parts & Accessories
These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water...
CA-0285
Location: Cube Molds
The Econ-O-Cube mold from Test Mark forms three 2-inch cubes at one time in a diagonal arrangement. Easy and secure online ordering.
SA-4010
Location: Dynamic Cone Penetrometer
The Dual Mass DCP Standard Kit from Test Mark measures the shear strength of soil with a CBR between 0.5 - 100%.
