Product Search
Search results for 'C91'
Showing 101 - 120 of 1123 Total Results
SA-2017
Location: CBR Accessories
Perforated 5-7/8" (149mm) dia. base with adjustable stem. Contact end of the stem is easily locked in place with a knurled nut.
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders. . The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of...
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
CA-3210
Location: Water/Cement Ratio
The Cementometer is used for rapid determination of the moisture content of fresh cement and concrete, available from Test Mark Industries.
CA-0700-02
Location: Concrete
Replacement cup and stopper for measuring concrete mortar in Chase air indicator testing.
CA-2950
Location: Comparator, Length Change
The Comparator from Test Mark Industries measures length changes of hardened cement paste, mortar, and concrete prismatic specimens.
AA-0015
Location: Marshall Basic Compression Testing
The dial indicator consists of a maximum position brake assembly and guide sleeve. Accommodates 4" or 6" breaking heads. Graduations of 0.01" div., range 1.00"...
(7) options
Location: Graduated Cylinders
Polypropylene graduated cylinders from Test Mark have a single scale with raised numerals for easy reading.
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers. . The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel...
(3) options
Location: Liquid Limit Testing Machines
Liquid limit machines from Test Mark are part of a complete line of soil testing equipment and supplies.
(8) options
Location: Cylinder Molds - Plastic
Test Mark Industries features plastic concrete cylinder molds as part of a complete line of concrete testing equipment.
(2) options
Location: Permeameters
The Compaction Permeameter from Test Mark is used for determining permeability of clay, sand and gravel soils using the Proctor plasticity compaction method.
CA-0355
Location: Concrete
The J-ring is used to determine the flowability and passing ability of self-consolidating concrete. Zinc plated for rust resistance.
Marshall Automatic Triple Compactor, 4" Rotating Mold
AA-0024
Location: Marshall Automatic Compactor
Automatically compacts three samples at a preset number of hammer blows and shuts off automatically on completion. Unit includes compactor, automatic counter, oak pedestal and 4" mold.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
(1) option
Location: Carrier Brackets for Masonry Platen
Easier and safer mounting of Block Platen. . The Carrier Bracket is used for safer removal and mounting of the block platen assembly inside the load frame, and should be considered a must have option when testing masonry units. The brackets heavy duty arm is mounted on the rear left hand corner of...
(4) options
Location: Test Platens
Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
SA-1800
Location: Soil Grinder
Soil grinder prepares soil samples to designated particle size for accurate and repeatable test results. Unit grinds a one-pint sample in 15 seconds. Includes a No. 10 perforated stainless plate.
Plastic Beam Mold 6" x 6" x 21"
CA-0340
Location: Plastic Beam Molds
Test Mark's durable, lightweight plastic beam mold uses simple thumbscrews for easy stripping, cleaning, and assembly.
