Product Search
Search results for 'D-2172'
Showing 221 - 240 of 1124 Total Results
Digital Static Cone Penetrometer
SA-1510
Location: Static Cone Penetrometer
Digital Static Cone Penetrometer from Test Mark features a large digital readout making testing and recording readings easy.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
(2) options
Location: Compaction Hammers
Soil Compaction Hammers from Test Mark are machined from steel and plated for rust resistance. Easy online ordering.
CA-2740
Location: Specific Gravity Bench
The Specific Gravity Bench from Test Mark weights suspended samples in water to determine specific gravity of aggregates and other materials.
(4) options
Location: Test Platens
Test both cubes and cylinders. Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
(3) options
Location: Test Platens
Used for testing 6” (152 mm) concrete cubes and cylinders in compression. The platens bearing block is 6.5” (152 mm) square, through hardened to HRC 55 or greater, plane to .0005” (.012 mm) in any 6” (152 mm) area, has concentric circles for easier centering of cylinders and is hard nickel plated...
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
CA-4052
Location: Sand Equivalent
The mechanical motor-driven sand equivalent shaker from Test Mark is recommended for performing sand equivalent tests on a regular basis.
CA-3210
Location: Water/Cement Ratio
The Cementometer is used for rapid determination of the moisture content of fresh cement and concrete, available from Test Mark Industries.
Location: Soils
Test Mark's COE Manual Compaction Hammer features a recoil mechanism in the foot assembly to reduce impact fatigue.
SA-0200
Location: Sand Density
The Sand Cone Density Apparatus from Test Mark Industries determines the in-place density of soils.
CA-0236
Location: Micrometer
This concrete micrometer was designed to accurately measure the diameter of concrete cylinders with a range of 5.5 - 6.5in.
CA-0286
Location: Cube Molds
The 2-inch cube maker molding system from Test Mark uses watertight polypropylene liners which fit into a 3-gang metal mold frame.
CA-2670
Location: Specific Gravity Flasks
The le chatelier flask from Test Mark is used to determine the relative density of cement or sand and other fine materials.
Marshall Automatic Single Compactor, 4" Stationary Mold
AA-0020
Location: Marshall Automatic Compactor
The Marshall Automatic Compactor apparatus from Test Mark compacts samples at a preset number of hammer blows and shuts off on completion.
CA-0356-L
Location: Self-Consolidating Concrete
L-Box Flowability is a method used to determine flow rates and passibility of SCC in confined spaces. Available from Test Mark Industries.
SA-0350-S
Location: Plastic Limit
Plastic Limit Test Set consists of glass plate, 250 ml evaporating dish, spatula, 48 - 2.5 oz. sample tins and a 100 ml graduated glass cylinder.
Voluvessel, 1/20 cu ft capacity
SA-1400
Location: Voluvessel
The Voluvessel from Test Mark is a direct reading instrument that is easily used and requires no calibration. A liquid filled balloon measures hole volume after removal of soil sample.
CA-3032
Location: Flow Tables
Measure is calibrated to 400 ml and is used to determine air content of hydraulic cement mortar. Cylindrical measure is 3" (76 mm) ID and approximately 3 15/32" (88 mm) deep.
