Product Search
Search results for 'T-176'
Showing 341 - 360 of 1124 Total Results
CA-2720
Location: Specific Gravity & Absorption Fine Aggregates
The conical mold and tamper from Test Mark are used to determine bulk and apparent specific gravity and absorption of fine aggregate.
(2) options
Location: 6" Cube Mold
This single cavity cube mold with base plate is used for compression testing of concrete cubes or mortar samples in the "Time of Initial" and "Final Setting" of concrete. Dimensions: 6" x 6" x 6" (152 x 152 x 152 mm).
Drive Tubes, 4" x 5.00" (101.6 x 127 mm), 10/pkg
SA-1372
Location: Density Drive Sampler
For use with Drive Sampler, 4" (101.6mm) x 5" (127mm) length, (4" x 0.033 ft3).
(4) options
Location: Retainers & Pads
Test Mark supplies grout sample unbonded capping system for compression testing of grout specimens in concrete testing environments.
CA-1400
Location: Lab Ovens
These gravity convection ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 0.7 cu. ft. model.
CA-1405
Location: Lab Ovens
These gravity convection ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 1.27 cu. ft. model.
CA-1410
Location: Lab Ovens
These gravity convection laboratory ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 2.0 cu. ft. model.
(3) options
Location: Spacers
Spacers are used to adjust the vertical testing height inside compression testing machine load frames when testing samples of various heights. Spacer mounts to the top cross head of the load frame. Spacer is manufactured from steel and is precision ground on both ends and painted for rust...
CA-0480
Location: Planeness/Thickness Gauges
Test Marks' steel parallel planeness gauge determines the planeness of testing machine platens, cylinder cappers and other testing accessories.
Test Mark Industries supplies calibration and service locations for its construction testing equipment.
(1) option
Location: Portable Scales
Test Mark pocket scales have a combination pan and cover that slides back for weighing and forward to cover the display and keys for storage or transport.
Stripping Tool, Aluminum Handle
CA-0240-A
Location: Stripping Tool
The durable stripping tool has a large easy-grip aluminum handle and a steel shaft. Quickly remove concrete specimens from single use plastic cylinder molds.
CA-0791
Location: Min/Max Thermometers
This Digital Thermometer registers minimum and maximum temperatures in both Fahrenheit and Celsius. Temperature range is 32 to 122°F and 0 to 50°C. Large display shows humidity, temperature and time. Thermometer also serves as an alarm clock.
Circulating Water Bath, Digital
AA-0065
Location: Circulating Water Bath
The circulating water bath from Test Mark is fully insulated with magnetic circulator for heating up to 12 4-inch diameter Marshall samples at a time.
CA-0970
Location: Test Hammer (Rebound)
The calibration test anvil from Test Mark Industries is used to check the calibration accuracy of a test hammer.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
SA-0245
Location: Shear Vane Tester
The pocket shear vane tester from Test Mark provides a quick and efficient method for determining shear strength values of cohesionless values of soils.
CA-3010
Location: Flow Tables
Motorized flow tables from Test Mark Industries are used to determine consistency of cement mortars. Features a 10-inch dia. cast bronze table.
CA-1320
Location: Hot Plates
Test Mark's laboratory hot plate features a white ceramic surface that is acid and alkali resistant. Non-heating frame surrounds the heated plate for added protection. Easy to set analog temperature control knob with graduated scale and LED display.
