Product Search
Search results for 'C-293'
Showing 101 - 120 of 1123 Total Results
(3) options
Location: Test Platens
Used for testing 6” (152 mm) concrete cubes and cylinders in compression . The platens bearing block is 6.5” (152 mm) square, through hardened to HRC 55 or greater, plane to .0005” (.012 mm) in any 6” (152 mm) area, has concentric circles for easier centering of cylinders and is hard nickel plated...
Drive Tubes, 3" x 2.75" (76.2 x 69.9 mm), 10/pkg
SA-1371
Location: Density Drive Sampler
For use with Drive Sampler, 3" (76.2mm) x 2.75" (69.9mm) length, (3" x 0.01 ft3). Accessory to the density drive sampler.
Marshall Automatic Single Compactor, 4" Stationary Mold
AA-0020
Location: Marshall Automatic Compactor
The Marshall Automatic Compactor apparatus from Test Mark compacts samples at a preset number of hammer blows and shuts off on completion.
CA-2160
Location: Door Enclosure
Lightweight, easily removable door panel designed to minimize dust and noise. Sturdy fiberboard door has a full-width hinge and sound deadening liner to cover the top and front openings.
(6) options
Location: Concrete Sensors
Durable, waterproof concrete sensors that monitor the environmental conditions within the concrete as it hardens. Models are available for both temperature and relative humidity monitoring.
CA-2560
Location: Sample Splitters
The adjustable sample splitter from Test Mark reduces aggregates to a suitable size and amount for gradation testing.
(3) options
Location: Vapor Emissions Test Kit
The vapor emission test method is specified by the Floor Covering Industry as the primary measure of moisture acceptable for floor covering or coating installations.
CA-0212
Location: Cylinder Transport
Sample cart is painted steel with two shelves. Overall dimensions 34" x 17" x 31 ½" (864 x 432 x 800 mm). Load capacity is 400 lbs. (181 kg). Ships unassembled.
CA-0280-P
Location: Cube Molds
The high-density polyethylene three-gang mold for 2-inch cubes strips and reassembles easily. Easy ordering online from Test Mark Industries.
High Strength Capping Compound
CA-0100-HS
Location: Capping Compound
Test Mark's High Strength Capping Compound is easily melted, pours smoothly, has a high compressive strength, and gives consistent test results.
SA-0245
Location: Shear Vane Tester
The pocket shear vane tester from Test Mark provides a quick and efficient method for determining shear strength values of cohesionless values of soils.
CA-0360
Location: Slump Testing
Slump cones from Test Mark Industries determine the slump of concrete in the laboratory or field. Easy and secure online ordering.
Speedy Moisture Reagent, 10 lb. can
SA-0262
Location: Soils
Calcium Carbide Reagent is used with the Speedy Moisture Tester to create pressure proportional to moisture in test samples. Supplied in 10-lb. can.
Pad Caps and Retainer Rings - Steel
(16) options
Location: Unbonded Capping (Retainers and Pad Caps)
Pad caps and retainer rings are available from Test Mark as part of a complete line of concrete testing equipment and supplies.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
CA-0285
Location: Cube Molds
The Econ-O-Cube mold from Test Mark forms three 2-inch cubes at one time in a diagonal arrangement. Easy and secure online ordering.
CA-4000
Location: Windsor Probe
The Windsor Probe from Test Mark evaluates the compressive strength of in-place concrete. Easy online ordering.
Capping Compound *TEMPORARILY OUT OF STOCK*
CA-0100
Location: Parts & Accessories
Test Mark's Ultra-Strength Capping Compound is used to cap the ends of concrete test cylinders so compression force will be evenly distributed to the cylinder during testing.
AA-0040-A
Location: Marshall Testing
Set includes Hand Compaction Hammer, 4" Compaction Mold, Compaction Pedestal with Top Plate, Hammer Support Rod with Adjustable Guide and Compaction Mold Holder.
SA-0350-S
Location: Plastic Limit
Plastic Limit Test Set consists of glass plate, 250 ml evaporating dish, spatula, 48 - 2.5 oz. sample tins and a 100 ml graduated glass cylinder.
