Product Search
Search results for 'T-304'
Showing 41 - 60 of 1648 Total Results
CA-3150
Location: Apparatus
The Gillmore Apparatus is used to determine initial and final set times of Portland cement, masonry cement, hydraulic hydrated lime and certain mortars.
CA-0933
Location: Specimen Curing
The curing tank immersion heater from Test Mark has an adjustable thermostat and a 1,000 watt 15 amp incolloy shielded heating element that resists rust.
Fresh Concrete Field Testing Kits, 6" x 12"
CA-0510
Location: Fresh Concrete Field Testing
Fresh concrete kits contain everythiung you need for routine testing of fresh concrete testing in the field, with all items meeting ASTM standards.
CA-0358
Location: Self-Consolidating Concrete
The V-Funnel is used to measure flowability of fresh self-consolidating concrete. The funnel is filled and the time taken for it to flow through the apparatus is measured. A valve on the outflow port can be closed to allow SCC to settle, which indicates the tendency for segregation.
Pad Caps and Retainer Rings - Steel
(16) options
Location: Unbonded Capping (Retainers and Pad Caps)
Pad caps and retainer rings are available from Test Mark as part of a complete line of concrete testing equipment and supplies.
Perpendicular Verification Device, 6" x 12" Cylinders
CA-0295
Location: Parts & Accessories
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
SA-4010
Location: Dynamic Cone Penetrometer
The Dual Mass DCP Standard Kit from Test Mark measures the shear strength of soil with a CBR between 0.5 - 100%.
CA-3210
Location: Water/Cement Ratio
The Cementometer is used for rapid determination of the moisture content of fresh cement and concrete, available from Test Mark Industries.
(3) options
Location: Test Platens
Used for testing 6” (152 mm) concrete cubes and cylinders in compression. The platens bearing block is 6.5” (152 mm) square, through hardened to HRC 55 or greater, plane to .0005” (.012 mm) in any 6” (152 mm) area, has concentric circles for easier centering of cylinders and is hard nickel plated...
Test Mark Industries supplies manuals and literature for its construction materials testing equipment products.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
CA-4000
Location: Windsor Probe
The Windsor Probe from Test Mark evaluates the compressive strength of in-place concrete. Easy online ordering.
CA-0610
Location: Air Entrainment/Roll-A-Meter
The lightweight aluminum Roll-A-Meter is used to determine the air content of concrete mixes, and is recommended for concrete containing lightweight aggregates, air-cooled slag or highly porous aggregates.
(2) options
Location: Rebar Locator
Test Mark's Rebarscope™ locates reinforcement bars in concrete and determines their depth and size.
CA-0191
Location: Parts & Accessories
Our pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set. These neoprene pad inserts are made from a tough...
CA-0191-50
Location: Parts & Accessories
Our pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Made from plated high-alloy steel to resist rust and deformation fatigue. Bearing surfaces machine-planed to within 0.002". Supplied two per set. These neoprene pad inserts are made from a tough...
Magnet Holder with Swivel Adapter Yoke
SA-2021
Location: CBR Accessories
Convenient, portable method of mounting dial indicators. Holder's Alnico magnetic base mounts on flat or curved metallic surfaces. Indicator can me mounted in almost any position.
Feeler Gauge Set, .002 to .025
CA-0485
Location: Planeness/Thickness Gauges
When used with the steel parallel bar, Test Mark's feeler gauge will determine the planeness of testing machine platens, cylinder cappers and other testing accessories.
CA-0910
Location: Parts & Accessories
The deluxe concrete curing box from Test Mark Industries can hold up to 22 standard 6 x 12 concrete test cylinders.
