Product Search
Search results for 'D1559'
Showing 61 - 80 of 1123 Total Results
AA-0300
Location: Asphalt Mixer
Test Mark's asphalt/concrete mixer is ideal for sample or batch mixing in either laboratory or field. Easy and secure ordering online.
(8) options
Location: Cylinder Molds - Plastic
Test Mark Industries features plastic concrete cylinder molds as part of a complete line of concrete testing equipment.
CA-4000
Location: Windsor Probe
The Windsor Probe from Test Mark evaluates the compressive strength of in-place concrete. Easy online ordering.
AA-0060
Location: Sample Ejector
Asphalt Sample Ejector from Test Mark is used for removing asphalt specimens from compaction molds.
Perpendicular Verification Device
(3) options
Location: Verification Device
The Perpendicular Verification Device is used to verify the alignment of 6" x 12" and 4" x 8" concrete cylinders when using un-bonded caps, as required by ASTM C-39. The device rests on the lower platen of the compression machine, avoiding contact with your retainer rings. Simply center the...
(4) options
Location: Desiccator Jar
The Desiccator Jar from Test Mark features a heavy walled annealed jar has finely ground flanges and cover knob.
CA-2170
Location: 30 Minute Timer
Plug aggregate equipment into the outlet at the back of the timer. Then plug timer cord into a wall outlet and turn the knob to the desired time. Time switch will turn off equipment automatically when time expires.
CA-0364
Location: Slump Testing
K-Slump Tester for in-place measurements indicates correlation to the slump test. The probe determines workability of concrete and the degree of compaction.
Aquaprobe™ Soil Moisture Meter
(2) options
Location: Soil Moisture Meters
Aquaprobe from Test Mark can determine the soil moisture content of different types of soils and other fine aggregate.
CA-3000
Location: Flow Tables
Hand driven flow tables are used to determine consistency of cement mortars. A test specimen is molded on the table to a specified volume and shape.
CA-2080
Location: Sieve Storage Rack
This adjustable bench rack holds all diameters of sieves up to 12" (305mm) maximum. Stainless steel rack has non-skid rubber feet, and two permanent and two adjustable rubber-coated sieve support rods.
Clear Calibrated Tube Assembly
CA-0600-02P
Location: Parts & Accessories
Clear calibrated tube assembly. Plastic Roll-A-Meter Kit replacement parts.
AA-2000
Location: Reflux Extractor
The Reflux Extractor Set from Test Mark, used for asphalt testing, features 2 cones, each with a 1000g capacity.
Concrete Cylinder Length Measuring Device for 4 & 6''Dia-24''L
CA-0237
Location: Core Length
With the core length measuring device measurements can be taken at the center point of the sample's upper end as well as the 8 equidistant points along the circumference.
44 Gallon Water Tank - 24" x 18" x 24" deep (610 x 457 x 610 mm). Max. Oper. Temp. - 140°F (60°C)
CA-2744
Location: Parts & Accessories
Seamless, translucent tanks are ¼" (6.4 mm) thick with a drain faucet and overflow outlet. 44 gallon tank is 24" x 18" x 24" deep (610 x 457 x 610 mm). Maximum operating temperature is 140°F (60° C).
SA-2013
Location: CBR Accessories
CBR Penetration Piston has 3 sq. in. (19.35cm2) base area and is about 7-1/2" (191mm) long. Designed for use in conjunction with weights to apply penetration surcharge loads.
CA-0212
Location: Cylinder Transport
Sample cart is painted steel with two shelves. Overall dimensions 34" x 17" x 31 ½" (864 x 432 x 800 mm). Load capacity is 400 lbs. (181 kg). Ships unassembled.
(4) options
Location: Dial Thermometers
Test Mark features Dial Thermometers as part of a complete line of materials testing equipment. Easy online ordering.
Constant Head Permeameter Cell
(5) options
Location: Permeameter Cell
The Constant Head Permeameter Cell from Test Mark is used to determine the coefficient of permeability by the constant head method for laminar flow of water through granular soils.
