Product Search
Search results for 'T283'
Showing 61 - 80 of 1647 Total Results
(2) options
Location: Rebar Locator
Test Mark's Rebarscope™ locates reinforcement bars in concrete and determines their depth and size.
(3) options
Location: Vertical Cappers
Test Mark's heavy-duty vertical cappers are used to apply molten capping compound to the ends of concrete cylinders for compression testing and insure the testing forces will be evenly distributed over the ends of the test cylinder.
(4) options
Location: Test Platens
Test both cubes and cylinders. Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
8" Pressure Meter Lid Seal and Piston Seal for CM-4000 series Machines
CA-0500-23
Location: Parts & Accessories
Lid seal, 8 inch. Pressure meter replacement parts; Test Mark Industries.
AA-0068
Location: Vacuum Pycnometer (Rice Test)
The vacuum pycnometer from Test Mark is used for determining the maximum specific gravity of bituminous paving mixtures with a maximum aggregate size up to 3/4-inch and a 2,000 g capacity.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
CA-0470
Location: Rubber Mallet
The rubber mallet from Test Mark is used to consolidate materials and release entrapped air in concrete molds, air meters, slump cones and unit weight buckets.
CA-1400
Location: Lab Ovens
These gravity convection ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 0.7 cu. ft. model.
CA-1405
Location: Lab Ovens
These gravity convection ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 1.27 cu. ft. model.
CA-1410
Location: Lab Ovens
These gravity convection laboratory ovens are used for drying, baking, sterilizing, evaporating, heat-treating, and testing. 2.0 cu. ft. model.
CA-0275-M
Location: Parts & Accessories
This single cavity cube mold with base plate is used for compression testing of concrete cubes or mortar samples in the "Time of Initial" and "Final Setting" of concrete. 150 mm steel model.
Material Handling Pan, 15" x 30" x 4" deep (381 x 762 x 102mm)
CA-2480
Location: Parts & Accessories
Steel handling pans have a chute end and swing down handles to permit oven access. 15" by 13" by 4" deep model.
Material Handling Pan, 12" x 20.5" x 4" deep (305 x 521 x 102mm)
CA-2485
Location: Parts & Accessories
Steel handling pans have a chute end and swing down handles to permit oven access. 12" x 20.5" x 4" deep model.
Vebe Consistometer, ASTM C1170
CA-0374
Location: Parts & Accessories
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete. The sample is placed in the mold and the surcharge weight is placed on top. The vibrator is started and the time for the concrete to consolidate and form a mortar ring is recorded. The surcharge is...
Vebe Consistometer, ASTM C1176
CA-0376
Location: Parts & Accessories
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete. The sample is placed in the mold and the surcharge weight is placed on top. The vibrator is started and the time for the concrete to consolidate and form a mortar ring is recorded. The surcharge is...
2" x 4" (50 x 102 mm) Black Plastic Mold no lip 75/ctn
CA-0232
Location: Parts & Accessories
Molds are injected plastic for close tolerances and consistency of shape. Molded, ribbed configuration gives added strength. Seamless design prevents moisture loss. Shipped 75 per carton. Plastic lids are sold separately.
CA-0610
Location: Air Entrainment/Roll-A-Meter
The lightweight aluminum Roll-A-Meter is used to determine the air content of concrete mixes, and is recommended for concrete containing lightweight aggregates, air-cooled slag or highly porous aggregates.
(4) options
Location: Manual Compression Testing Machines
Testing range of 5,000 to 500,000 lbs. (22.2 – 2,224 kN) with an accuracy of ±.5% of indicated load., Frame stiffness rating of 41.6 million lbs/in., Easier specimen loading with large platen table.. Request a Quote Our CM-5000 series machines feature rigid distortion-resistant load frames designed...
SA-1124
Location: Parts & Accessories
Acrylic tank features a regulating valve for flow control of water, a porous media on the bottom to filter out air bubbles and an overflow port. Unit includes saddle valve for connection to water source, rails for wall mounting and tubing for hook-up to test chamber.
