WOC 2024

Product Search

Search results for 'D6931'

Showing 1 - 20 of 1123 Total Results

Lottman Breaking Head, 4"

AA-0012

Location: Marshall Basic Compression Testing

Lottman breaking heads are used for testing tensile strength; 4" model.

Lottman Breaking Head, 6"

AA-0013

Location: Marshall Basic Compression Testing

Lottman breaking heads are used for testing tensile strength; 6" model.

Marshall Breaking Head, 4"

AA-0010

Location: Marshall Basic Compression Testing

The lower segment of Test Mark's Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments.

Marshall Breaking Head, 6"

AA-0011

Location: Marshall Basic Compression Testing

The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.

Tensile Sand

CA-2910

Location: Cube Molds

Tensile sand from Test Mark Industries is specially graded natural silica sand to pass a No. 20 (850 um) sieve.

High Strength Capping Compound

CA-0100-HS

Location: Capping Compound

Test Mark's High Strength Capping Compound is easily melted, pours smoothly, has a high compressive strength, and gives consistent test results.

Dial Flowmeter

AA-0015

Location: Marshall Basic Compression Testing

The dial indicator consists of a maximum position brake assembly and guide sleeve. Accommodates 4" or 6" breaking heads. Graduations of 0.01" div., range 1.00"...

Machine Accessory Lift

MA-1101

Location: Machine Accessory Lift

The machine accessory lift can raise 1,100 pounds easily with a detachable metal handle - changing out breaking heads or adding spacers is quick and easy.

Constant/Falling Head Permeameter Set

(5) options

Location: Permeameter Sets

Constant/Falling Head Permeameter Set for use with granular soils in determining the coefficient of permeability via the constant or falling-head method for laminar flow of water.

Constant Head Permeameter Cell

(5) options

Location: Permeameter Cell

The Constant Head Permeameter Cell from Test Mark is used to determine the coefficient of permeability by the constant head method for laminar flow of water through granular soils.

Capping Compound *TEMPORARILY OUT OF STOCK*

CA-0100

Location: Parts & Accessories

Test Mark's Ultra-Strength Capping Compound is used to cap the ends of concrete test cylinders so compression force will be evenly distributed to the cylinder during testing.

CM-30 Series

(5) options

Location: Manual Compression Testing Machines

Testing range of 300 to 30,000 lbs. (1.3 to 133.5 kN) with an accuracy of ±.5% of indicated load., Compact design requires minimal floor space.. Request a Quote The CM-30 was developed for testing concrete beams where accuracy and maintaining their required load pacing rate is an essential part of...

Masonry Series Testing Machines

(8) options

Location: Manual Compression Testing Machines

Test blocks, masonry prisms, pavers and retaining wall units., Testing range from 1% to full machine capacity, with an accuracy of ±.5% of indicated load., Optional accessories for testing a full range of concrete and cement products.. Request a Quote Masonry series machines are available in two...

Density Drive Sampler, 4" (101.6 mm)

SA-1360

Location: Density Drive Sampler

The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 4" model.

Cylinder Splitting Set

(3) options

Location: Test Platens

Used to determine the splitting tensile strength of concrete cylinders.. The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of test...

High Capacity Series Compression Testing Machines

(3) options

Location: Manual Compression Testing Machines

Accuracy range of ±.5% of indicated load from 1% to machine capacity.. Request a Quote High capacity series machines feature rigid distortion-resistant load frames that are designed to meet the demands of testing high-performance concrete in a production testing program, where accurate and...

CM-2500 Series

(8) options

Location: Manual Compression Testing Machines

Testing range of 2,500 to 250,000 lbs. (11 – 1,112 kN) with an accuracy of ±.5% of indicated load., Supplied with platen set for testing 6" x 12" (150 x 300 mm) cylinders using unbonded or sulfur capping method and steel safety guard doors., Continuous duty hydraulic pump runs quieter, cooler and...

Density Drive Sampler, 3" ( 76.2 mm)

SA-1355

Location: Density Drive Sampler

The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 3" model.

Mortar, 320 ml

SA-0650

Location: Mortar & Pestle

Soil mortar, when used with the pestle, is for pulverizing dry samples of soil and other materials. Mortar is made from heavy porcelain with glazed exterior. Rubber-tipped pestle is 8" long and is for grinding soils without breaking individual particles.

TS17 Touchscreen Load Indicating System

TS17

Location: Digital Load Indicating Systems

Test Mark is proud to introduce the TS17 touchscreen digital load indicating system for concrete compression testing machines. The controller’s 7'' full color waterproof screen uses large, easy-to-read, alphanumeric characters to simultaneously display live load, sample stress, and rate of loading...